Cabletron Systems 2200 manual Cabletron SYSTEMS, INC Program License Agreement

Page 5

CABLETRON SYSTEMS, INC.

PROGRAM LICENSE AGREEMENT

IMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE FOLLOWING GEOGRAPHICAL REGIONS:

CANADA

MEXICO

CENTRAL AMERICA

SOUTH AMERICA

BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT.

This document is an agreement (“Agreement”) between You, the end user, and Cabletron Systems, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron software program (“Program”) in the package. The Program may be contained in firmware, chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED PRODUCT TO CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND.

IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON SYSTEMS +1- 603-332-9400. Attn: Legal Department.

1.LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the United States or as authorized in writing by Cabletron.

2.OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.

3.APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and venue of the New Hampshire courts.

4.EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain countries, unless a license to export the product is obtained from the U.S. Government or an exception from obtaining such license may be relied upon by the exporting party.

If the Program is exported from the United States pursuant to the License Exception CIV under the U.S. Export Administration Regulations, You agree that You are a civil end user of the Program and agree that You will use the Program for civil end uses only and not for military purposes.

iii

Image 5
Contents 2E253-49R SmartSwitch Installation User’s Guide Page Page FCC Notice Cabletron SYSTEMS, INC Program License Agreement Page Page Page Cabletron Systems Limited Program License Agreement Viii Declaration of Conformity Page Contents Troubleshooting Figures Tables Structure of this Guide Using this GuideAbout This Guide Xvi Related DocumentsDocument Conventions Document ConventionsPage Overview IntroductionConnectivity Full Duplex Switched EthernetSmartTrunk Standard/Full Duplex Auto-NegotiationRuntime IP Address Discovery Port/VLAN Redirect Functions Remote Monitoring RmonBroadcast Suppression Flow Control Traffic Rate LimitingSwitching Options Garp Switch Operation12 802.1 Port Priority ManagementOptional HSIMs and VHSIMs Lanview Diagnostic LEDsStandards Compatibility Year 2000 ComplianceFTP Getting Help10BASE-T Network Network RequirementsPage Installation Unpacking the Device Installing OptionsTabletop or Shelf Installation Installing the DeviceGuidelines for the Rackmount Installation Rackmount InstallationAttaching the Strain-Relief Bracket Rack Mounting the 2E253-49R Installing the Device in a Rack Connecting PowerRedundant Primary AC outlets are On separate circuits Connecting to the NetworkConnection Using the RJ21 Angle Adapter Completing the Installation Using Lanview TroubleshootingPWR No link Is enabled and there is a OFF Troubleshooting Checklist2E253, 2H252, 2H253, and 2H258 Local Reset Button Using the Reset ButtonPage Physical Properties Device SpecificationsSpecifications INPUT/OUTPUT Ports Electrical SpecificationsEnvironmental Requirements Regulatory Compliance COM Port Pinout AssignmentsPage Required Tools Optional Installations Mode Switch Bank SettingsRemoving the Chassis Cover To remove the chassis cover, proceed as follows Screws Chassis Cover Front Panel Switch 6 Forced BootP Setting the Mode SwitchesSimm Upgrade Locating SIMMs Figure B-3shows the location of the Dram Simm connectorSimm Installing the Dram SimmFigure B-5 Hsim and Vhsim Connector Locations Installing Optional Hsim or Vhsim Interface ModulesPage Numerics IndexIndex-2