Brocade Communications Systems 53-1002599-01 manual Brocade ICX 6650 maintenance

Page 49

	Brocade ICX 6650 maintenance		4
4x10 GbE GSFP+ rear port LEDs on front panel
LED State	Status of hardware	Recommended action
Off (no light)	Not enabled.	No action required.
Green	Link is up in 10 GbE mode.	No action required.
Blinking green	Indicates activity, and packets are being	No action required.
	transmitted or received.

Brocade ICX 6650 maintenance

The ICX 6650 is designed for high availability and low failure; it does not require any regular physical maintenance. Supported transceivers and diagnostic tests are described in the following sections.

Diagnostic tests and monitoring

Brocade Network OS includes diagnostic tests to help you troubleshoot the hardware. System diagnostic software is designed to fulfill the purpose of off-line diagnostics. In off-line diagnostics, you have to turn ON/OFF the diagnostic flags to execute diagnostic tests during the next boot-up.

The CLI commands for system diagnostic tests are dm diag and dm alt-diag. These diagnostic tests verify all available hardware components including:

•I2C devices

•EEPROMS

•CPU packet

•Test MAC alignment

•Line rate

During system diagnostic testing, the system is completely under the control of the diagnostic software. All hardware components are verified, and results are displayed on the console. In cases where a failure is detected, results and corrective actions will be displayed. After the system diagnostic testing is complete, the system exits from the diagnostic mode and reloads the system for normal operation.

System diagnostic testing runs at link speeds 10 Gbps and 40 Gbps (QSFP ports) depending on the speed of the link being tested and the type of port.

Brocade ICX 6650 Hardware Installation Guide	33
53-1002599-01

Image 49

Contents Brocade ICX Brocade Communications Systems, Incorporated Contents Chapter Configuring the Brocade ICX Appendix C Brocade ICX 6650 Cautions and Danger Notices Index Figures Brocade ICX 6650 Installation Guide Tables Brocade ICX 6650 Ethernet Installation Guide Audience About This DocumentSupported hardware and software Brocade ICX 6650 slot and Ethernet port numberingHow this document is organized Document conventions Command syntax conventionsText formatting Corporation Referenced Trademarks and Products Related publicationsGetting technical help Additional informationDocument feedback Brocade resourcesBrocade ICX 6650 slot and Ethernet port numbering This chapter Brocade ICX 6650 OverviewBrocade ICX 6650 overview 3 4 Views of the Brocade ICX 6650 switchShows the rear-panel ports Ports-on-Demand licensingBrocade ICX 6650 slot and Ethernet port numbering Supported transceivers and cables Breakout cables Package contents Installing the Brocade ICXUnpacking the device Electrical considerations Installation and safety considerationsEnvironmental considerations Location ConsiderationsRecommendations for cable management Cabinet considerationsInstallation precautions Installation tasksGeneral precautions Power precautions Lifting precautionsInstalling the device in a rack or cabinet Post rack mount installation Proceed to Attaching a PC or terminal on Show exploded views of the optional 4-post rack mount kit Optional 4-post Rack Mount Kit, Rear Attach Attaching a PC or terminal Powering on the systemInstalling an SFP+ transceiver in a port slot Installing an SFP+ transceiverConfiguring the Brocade ICX Assigning permanent passwords Recovering from a lost password Setting passwordsDevices running Layer 2 software Configuring IP addressesDevices running Layer 3 software Syntax no ip address ip-addr/mask-bitssecondary Syntax router-interface ve num Syntax interface ve num Connectors Connecting network devicesConnecting a network device to a fiber port Installing a transceiver Troubleshooting network connections Testing connectivityPinging an IP address Tracing a routeLED activity interpretation Brocade ICX 6650 OperationBrocade ICX 6650 front panel LEDs Brocade ICX 6650 front panel LEDs and port numbering Shows the LEDs on the rear panel of the Brocade ICX Brocade ICX 6650 rear panel LEDsPSU 1 and PSU2 LED patternsDiagnostic tests and monitoring Brocade ICX 6650 maintenanceDiagnostic tests and monitoring Managing the Brocade ICX Managing temperature settingsDisplaying the temperature Changing the temperature warning level Displaying Syslog messages for temperatureChanging the temperature poll time Removing MAC address entries Hardware maintenance scheduleDisplaying Brocade ICX 6650 CPU usage Removing a copper or fiber optic module Replacing a copper or fiber optic moduleCleaning the fiber optic connectors FRU removal and replacement proceduresCabling a fiber optic module Replacing a power supply unit Replacing a power supply Determining the need to replace a power supplyTime and items required Replacing fan trays Replacing the fan assembly Determining the need to replace a fan assemblyWeight and physical dimensions Brocade ICX 6650 SpecificationsThis appendix Cooling system and fans Environmental considerationsAirflow Intake airflow label General specifications Power supply specificationsMemory specifications Pinouts and signallingSupported media types USA FCC CFR 47 Part 15 Warning Brocade ICX 6650 Regulatory StatementsIndustry Canada statement Germany Noise Warning Europe and Australia Cispr 22 Class a WarningJapan Vcci Korea Japan power cordChina Regulatory compliance Bsmi statement TaiwanRegulatory compliance Brocade ICX 6650 Cautions and Danger Notices Vorsicht Devices near the input power connectors Never leave tools inside the chassis Vorsicht Orangefarbenen Pfeil mit dem Buchstaben I gekennzeichnet Gefahr Schwerer desto tiefer darüber untergebracht werden Remove both power cords before servicing Brocade ICX 6650 Hardware Installation Guide Numerics IndexBrocade ICX 6650 Hardware Installation Guide Brocade ICX 6650 Hardware Installation Guide 53-1002599-01 Brocade ICX 6650 Hardware Installation Guide