Brocade Communications Systems 53-1002599-01 manual Replacing a copper or fiber optic module

Page 55

Replacing a copper or fiber optic module

5

Replacing a copper or fiber optic module

You can remove an SFP+ or QSFP+ transceiver from a slot and replace it with a new one while the Brocade ICX 6650 is powered on and running.

This section provides information about the following tasks:

Removing a copper or fiber optic module

Installing a new copper or fiber optic module

Cabling a fiber optic module

Removing a copper or fiber optic module

You can remove a copper or fiber SFP, SFP+, or QSFP+ transceiver from a slot while the Brocade ICX 6650 is powered on and running.

While removing a copper or fiber optic module, be sure to wear an ESD wrist strap with a plug that can be inserted in the ESD connector on the Brocade ICX 6650.

CAUTION

For safety reasons, the ESD wrist strap should contain a series 1 megohm resistor.

To remove a copper or fiber optic module from an SFP slot, do the following.

1.Put on the ESD wrist strap and ground yourself by attaching the clip end to a metal surface (such as an equipment rack).

2.Disconnect the copper or fiber cable connector from the port connector.

3.Unlock the copper or fiber optic module by pulling the bail latch forward, away from the front panel of the module.

On 1000BaseSX ports, the bail latch is enclosed in a black sleeve, and on 1000BaseLX ports, the bail latch is enclosed in a blue sleeve.

FIGURE 16 Unlocking the bail latch

1

1 Bail Latch

NOTE

The bail latch may be attached to either the top or the bottom of the mini-GBIC.

Brocade ICX 6650 Hardware Installation Guide

39

53-1002599-01

 

Image 55
Contents Brocade ICX Brocade Communications Systems, Incorporated Contents Chapter Configuring the Brocade ICX Appendix C Brocade ICX 6650 Cautions and Danger Notices Index Figures Brocade ICX 6650 Installation Guide Tables Brocade ICX 6650 Ethernet Installation Guide Brocade ICX 6650 slot and Ethernet port numbering About This DocumentAudience Supported hardware and softwareHow this document is organized Document conventions Command syntax conventionsText formatting Corporation Referenced Trademarks and Products Related publicationsBrocade resources Additional informationGetting technical help Document feedbackBrocade ICX 6650 slot and Ethernet port numbering This chapter Brocade ICX 6650 OverviewBrocade ICX 6650 overview 3 4 Views of the Brocade ICX 6650 switchShows the rear-panel ports Ports-on-Demand licensingBrocade ICX 6650 slot and Ethernet port numbering Supported transceivers and cables Breakout cables Package contents Installing the Brocade ICXUnpacking the device Location Considerations Installation and safety considerationsElectrical considerations Environmental considerationsRecommendations for cable management Cabinet considerationsInstallation precautions Installation tasksGeneral precautions Power precautions Lifting precautionsInstalling the device in a rack or cabinet Post rack mount installation Proceed to Attaching a PC or terminal on Show exploded views of the optional 4-post rack mount kit Optional 4-post Rack Mount Kit, Rear Attach Attaching a PC or terminal Powering on the systemInstalling an SFP+ transceiver in a port slot Installing an SFP+ transceiverConfiguring the Brocade ICX Assigning permanent passwords Recovering from a lost password Setting passwordsDevices running Layer 2 software Configuring IP addressesDevices running Layer 3 software Syntax no ip address ip-addr/mask-bitssecondary Syntax router-interface ve num Syntax interface ve num Connectors Connecting network devicesConnecting a network device to a fiber port Installing a transceiver Tracing a route Testing connectivityTroubleshooting network connections Pinging an IP addressLED activity interpretation Brocade ICX 6650 OperationBrocade ICX 6650 front panel LEDs Brocade ICX 6650 front panel LEDs and port numbering Shows the LEDs on the rear panel of the Brocade ICX Brocade ICX 6650 rear panel LEDsPSU 1 and PSU2 LED patternsDiagnostic tests and monitoring Brocade ICX 6650 maintenanceDiagnostic tests and monitoring Managing the Brocade ICX Managing temperature settingsDisplaying the temperature Changing the temperature warning level Displaying Syslog messages for temperatureChanging the temperature poll time Removing MAC address entries Hardware maintenance scheduleDisplaying Brocade ICX 6650 CPU usage Removing a copper or fiber optic module Replacing a copper or fiber optic moduleCleaning the fiber optic connectors FRU removal and replacement proceduresCabling a fiber optic module Replacing a power supply unit Replacing a power supply Determining the need to replace a power supplyTime and items required Replacing fan trays Replacing the fan assembly Determining the need to replace a fan assemblyWeight and physical dimensions Brocade ICX 6650 SpecificationsThis appendix Cooling system and fans Environmental considerationsAirflow Intake airflow label General specifications Power supply specificationsMemory specifications Pinouts and signallingSupported media types USA FCC CFR 47 Part 15 Warning Brocade ICX 6650 Regulatory StatementsIndustry Canada statement Germany Noise Warning Europe and Australia Cispr 22 Class a WarningJapan Vcci Korea Japan power cordChina Regulatory compliance Bsmi statement TaiwanRegulatory compliance Brocade ICX 6650 Cautions and Danger Notices Vorsicht Devices near the input power connectors Never leave tools inside the chassis Vorsicht Orangefarbenen Pfeil mit dem Buchstaben I gekennzeichnet Gefahr Schwerer desto tiefer darüber untergebracht werden Remove both power cords before servicing Brocade ICX 6650 Hardware Installation Guide Numerics IndexBrocade ICX 6650 Hardware Installation Guide Brocade ICX 6650 Hardware Installation Guide 53-1002599-01 Brocade ICX 6650 Hardware Installation Guide