Brocade Communications Systems 53-1002599-01 manual FRU removal and replacement procedures

Page 56

5 FRU removal and replacement procedures

4. Grasp the bail latch and pull the copper or fiber optic module out of the port.

FIGURE 17 Remove fiber optic module

5.Store the copper or fiber optic module in a safe, static-free place or in an anti-static bag.

6.Install a new copper or fiber optic module in the port.

Cabling a fiber optic module

For instructions on cabling a fiber optic module refer to “Cabling a fiber optic transceiver” on page 34.

Cleaning the fiber optic connectors

For instructions on cleaning a fiber optic module refer to “Cleaning the fiber optic connectors” on page 35.

FRU removal and replacement procedures

The field-replaceable units (FRUs) in the Brocade ICX 6650 can be removed and replaced without special tools. The switches can continue operating during the FRU replacement if the conditions specified in these procedures are followed. This covers both the power supply unit (PSU) FRUs and fan FRUs.

CAUTION

This document describes how to change FRUs for units with either an air intake or air exhaust. You must replace a failed FRU with a FRU of the same type. This applies to both power supplies and fans. A new FRU must have the same part number (P/N) as the FRU being replaced. The manufacturing P/N is located on the top of the FRU.

If a mismatched power source or fan assembly is installed by mistake, a warning is sent to the console. The warning messages will be similar to the following:

•For a fan mismatch: [WARNING, Brocade ICX 6650, MISMATCH in Fan Air Flow direction. Replace FRU with fan air flows in the same direction.

•For a power supply: [WARNING, Brocade ICX 6650, MISMATCH in PSU Air Flow direction. Replace PSU with air flows in the same direction

40	Brocade ICX 6650 Hardware Installation Guide
	53-1002599-01

Image 56

Contents Brocade ICX Brocade Communications Systems, Incorporated Contents Chapter Configuring the Brocade ICX Appendix C Brocade ICX 6650 Cautions and Danger Notices Index Figures Brocade ICX 6650 Installation Guide Tables Brocade ICX 6650 Ethernet Installation Guide About This Document AudienceSupported hardware and software Brocade ICX 6650 slot and Ethernet port numberingHow this document is organized Text formatting Command syntax conventionsDocument conventions Related publications Corporation Referenced Trademarks and ProductsAdditional information Getting technical helpDocument feedback Brocade resourcesBrocade ICX 6650 slot and Ethernet port numbering Brocade ICX 6650 overview Brocade ICX 6650 OverviewThis chapter Views of the Brocade ICX 6650 switch 3 4Ports-on-Demand licensing Shows the rear-panel portsBrocade ICX 6650 slot and Ethernet port numbering Supported transceivers and cables Breakout cables Unpacking the device Installing the Brocade ICXPackage contents Installation and safety considerations Electrical considerationsEnvironmental considerations Location ConsiderationsCabinet considerations Recommendations for cable managementGeneral precautions Installation tasksInstallation precautions Lifting precautions Power precautionsInstalling the device in a rack or cabinet Post rack mount installation Proceed to Attaching a PC or terminal on Show exploded views of the optional 4-post rack mount kit Optional 4-post Rack Mount Kit, Rear Attach Powering on the system Attaching a PC or terminalInstalling an SFP+ transceiver Installing an SFP+ transceiver in a port slotConfiguring the Brocade ICX Assigning permanent passwords Setting passwords Recovering from a lost passwordConfiguring IP addresses Devices running Layer 2 softwareDevices running Layer 3 software Syntax no ip address ip-addr/mask-bitssecondary Syntax router-interface ve num Syntax interface ve num Connecting a network device to a fiber port Connecting network devicesConnectors Installing a transceiver Testing connectivity Troubleshooting network connectionsPinging an IP address Tracing a routeBrocade ICX 6650 front panel LEDs Brocade ICX 6650 OperationLED activity interpretation Brocade ICX 6650 front panel LEDs and port numbering Brocade ICX 6650 rear panel LEDs Shows the LEDs on the rear panel of the Brocade ICXLED patterns PSU 1 and PSU2Brocade ICX 6650 maintenance Diagnostic tests and monitoringDiagnostic tests and monitoring Managing temperature settings Managing the Brocade ICXDisplaying the temperature Changing the temperature poll time Displaying Syslog messages for temperatureChanging the temperature warning level Displaying Brocade ICX 6650 CPU usage Hardware maintenance scheduleRemoving MAC address entries Replacing a copper or fiber optic module Removing a copper or fiber optic moduleCabling a fiber optic module FRU removal and replacement proceduresCleaning the fiber optic connectors Replacing a power supply unit Time and items required Determining the need to replace a power supplyReplacing a power supply Replacing fan trays Determining the need to replace a fan assembly Replacing the fan assemblyThis appendix Brocade ICX 6650 SpecificationsWeight and physical dimensions Environmental considerations Cooling system and fansAirflow Intake airflow label Power supply specifications General specificationsSupported media types Pinouts and signallingMemory specifications Industry Canada statement Brocade ICX 6650 Regulatory StatementsUSA FCC CFR 47 Part 15 Warning Japan Vcci Europe and Australia Cispr 22 Class a WarningGermany Noise Warning Japan power cord KoreaChina Bsmi statement Taiwan Regulatory complianceRegulatory compliance Brocade ICX 6650 Cautions and Danger Notices Vorsicht Devices near the input power connectors Never leave tools inside the chassis Vorsicht Orangefarbenen Pfeil mit dem Buchstaben I gekennzeichnet Gefahr Schwerer desto tiefer darüber untergebracht werden Remove both power cords before servicing Brocade ICX 6650 Hardware Installation Guide Index NumericsBrocade ICX 6650 Hardware Installation Guide Brocade ICX 6650 Hardware Installation Guide 53-1002599-01 Brocade ICX 6650 Hardware Installation Guide