Brocade Communications Systems 53-1002599-01 manual Replacing fan trays

Page 59

Replacing fan trays

5

4.Ensure that the replacement power supply has the same part number and airflow label as the power supply being replaced.

5.Unplug the power cord from the power supply that is being replaced.

6.Using the Phillips screwdriver, unscrew the two captive screws on the power supply.

7.Remove the power supply from the chassis by pulling the handle on the power supply out and away from the chassis.

8.Holding the power supply level, guide it into the carrier rails on each side and gently push it all the way into the slot, ensuring that it firmly engages with the connector.

9.When you are sure the power supply has properly engaged the connector, tighten the retainer screws to secure the power supply in the slot.

10.Plug the power cord into the power supply to power on the unit. The power supply will immediately attempt to power up.

11.Verify that the LED on the new power supply displays steady green while the Brocade ICX 6650 is operating (see Table 2). If the LED is not steady green, ensure that the power supply is securely installed and seated properly.

You can enter the show chassis command at the command line prompt to display power supply status.

CAUTION

Do not force the installation. If the power supply does not slide in easily, ensure that the power supply is correctly oriented before continuing.

Replacing fan trays

CAUTION

For the Brocade ICX 6650 devices, be sure that the airflow direction of the fan tray matches that of the installed power supply unit. The power supplies and fan trays are clearly labeled with either a green arrow with an “E”, or an orange arrow with an “I.”

The Brocade ICX 6650 includes two redundant, hot-swappable fan units.

ATTENTION

Maintain all power supply and fan assemblies in operational condition to provide redundancy.

CAUTION

Because the cooling system relies on pressurized air, do not leave any of the power supply and fan assembly slots empty longer than two minutes while the switch is operating. If a power supply or fan assembly fails, leave it in the switch until it can be replaced.

Brocade ICX 6650 Hardware Installation Guide	43
53-1002599-01

Image 59

Contents Brocade ICX Brocade Communications Systems, Incorporated Contents Chapter Configuring the Brocade ICX Appendix C Brocade ICX 6650 Cautions and Danger Notices Index Figures Brocade ICX 6650 Installation Guide Tables Brocade ICX 6650 Ethernet Installation Guide Brocade ICX 6650 slot and Ethernet port numbering About This DocumentAudience Supported hardware and softwareHow this document is organized Text formatting Command syntax conventionsDocument conventions Corporation Referenced Trademarks and Products Related publicationsBrocade resources Additional informationGetting technical help Document feedbackBrocade ICX 6650 slot and Ethernet port numbering Brocade ICX 6650 overview Brocade ICX 6650 OverviewThis chapter 3 4 Views of the Brocade ICX 6650 switchShows the rear-panel ports Ports-on-Demand licensingBrocade ICX 6650 slot and Ethernet port numbering Supported transceivers and cables Breakout cables Unpacking the device Installing the Brocade ICXPackage contents Location Considerations Installation and safety considerationsElectrical considerations Environmental considerationsRecommendations for cable management Cabinet considerationsGeneral precautions Installation tasksInstallation precautions Power precautions Lifting precautionsInstalling the device in a rack or cabinet Post rack mount installation Proceed to Attaching a PC or terminal on Show exploded views of the optional 4-post rack mount kit Optional 4-post Rack Mount Kit, Rear Attach Attaching a PC or terminal Powering on the systemInstalling an SFP+ transceiver in a port slot Installing an SFP+ transceiverConfiguring the Brocade ICX Assigning permanent passwords Recovering from a lost password Setting passwordsDevices running Layer 2 software Configuring IP addressesDevices running Layer 3 software Syntax no ip address ip-addr/mask-bitssecondary Syntax router-interface ve num Syntax interface ve num Connecting a network device to a fiber port Connecting network devicesConnectors Installing a transceiver Tracing a route Testing connectivityTroubleshooting network connections Pinging an IP addressBrocade ICX 6650 front panel LEDs Brocade ICX 6650 OperationLED activity interpretation Brocade ICX 6650 front panel LEDs and port numbering Shows the LEDs on the rear panel of the Brocade ICX Brocade ICX 6650 rear panel LEDsPSU 1 and PSU2 LED patternsDiagnostic tests and monitoring Brocade ICX 6650 maintenanceDiagnostic tests and monitoring Managing the Brocade ICX Managing temperature settingsDisplaying the temperature Changing the temperature poll time Displaying Syslog messages for temperatureChanging the temperature warning level Displaying Brocade ICX 6650 CPU usage Hardware maintenance scheduleRemoving MAC address entries Removing a copper or fiber optic module Replacing a copper or fiber optic moduleCabling a fiber optic module FRU removal and replacement proceduresCleaning the fiber optic connectors Replacing a power supply unit Time and items required Determining the need to replace a power supplyReplacing a power supply Replacing fan trays Replacing the fan assembly Determining the need to replace a fan assemblyThis appendix Brocade ICX 6650 SpecificationsWeight and physical dimensions Cooling system and fans Environmental considerationsAirflow Intake airflow label General specifications Power supply specificationsSupported media types Pinouts and signallingMemory specifications Industry Canada statement Brocade ICX 6650 Regulatory StatementsUSA FCC CFR 47 Part 15 Warning Japan Vcci Europe and Australia Cispr 22 Class a WarningGermany Noise Warning Korea Japan power cordChina Regulatory compliance Bsmi statement TaiwanRegulatory compliance Brocade ICX 6650 Cautions and Danger Notices Vorsicht Devices near the input power connectors Never leave tools inside the chassis Vorsicht Orangefarbenen Pfeil mit dem Buchstaben I gekennzeichnet Gefahr Schwerer desto tiefer darüber untergebracht werden Remove both power cords before servicing Brocade ICX 6650 Hardware Installation Guide Numerics IndexBrocade ICX 6650 Hardware Installation Guide Brocade ICX 6650 Hardware Installation Guide 53-1002599-01 Brocade ICX 6650 Hardware Installation Guide