Extron electronic manual Configuring the IPL T CR48 using the ARP command

Page 27

Configuring the IPL T CR48 using the ARP command

You can make use of the ARP (Address Resolution Protocol) command to set up an IP address for your IPL T CR48 interface. The ARP command tells your computer to associate the

IPL T CR48 unit’s MAC address with the assigned IP address. You must then use Ping to access the IPL T CR48 unit, at which point the device server’s IP address will be reconfigured.

NIn order to use this setup method, both your computer and IPL T CR48 interface must be connected to the same LAN. Or, you may use a crossover Ethernet cable to connect the device server directly to your computer’s Ethernet card.

Use ARP to configure the IP address as follows:

1.Obtain a valid IP address for your IPL T CR48 from your network administrator.

2.Obtain the IPL T CR48 unit’s MAC address (UID #) from the label on its back panel.

3.If the unit has never been configured and is still set for factory defaults, go to step 4. If not, perform a Mode 4 system reset. For detailed information on reset modes, see “Resetting the unit” in chapter 2.

CYour IPL T CR48 unit must be configured with the factory default IP address — 192.168.254.254 — before executing the ARP command, as described below.

4.Access the MS-DOS command prompt, then execute the ‘arp –s’ command.

Enter the desired new IP address and the MAC address (the MAC address is located on the rear panel’s upper left corner) for the IPL unit. For example:

arp –s 10.13.170.15 00-05-A6-00-0A-90

IPL T CR48 • Connection and Configuration

3-5

Page 26 Page 28
Image 27
Page 26 Page 28
Contents IP Link Tools IPL T CR48Safety Instructions English PrecautionsFCC Class a Notice 安全须知 中文This page has been intentionally left blank IPL T CR48 Quick Start Guide QS-1 Quick Start Guide IPL T CR48QS-2 IPL T CR48 Quick Start Guide Quick Start Guide -­ IPL T CR48, cont’dTable of Contents Table of Contents, cont’d One About the IPL T CR48 Interface FeaturesIntroduction About this ManualEasily configured and controlled Introduction, cont’d Two Mounting the IPL T CR48 Installation and OperationInstallation Overview IPL T CR48 Installation and Operation1U Rack Shelf Furniture or projector mounting Installation and Operation, cont’dIPL T CR48 interface back panel Power Rear Panel Features and CablingEthernet/LAN ConnectionsIdentification Operation Example application using input and relay portsResetting the unit Front panel indicatorsIPL T CR48 Installation and Operation Installation and Operation, cont’d Three Ethernet connection Connection and ConfigurationConnecting the Hardware IPL T CR48 Connection and ConfigurationRelay connections IPL T CR48 Connection and ConfigurationIPL T CR48 interface configuration Connection and Configuration, cont’dConfiguring the Hardware PC configurationConfiguring the IPL T CR48 using the ARP command Executing the ARP command 255.255.0.0 Configuring the IPL T CR48 using direct PC connectionFirmware upgrades Four Relay ports Communication and ControlPorts Overview Contact closure input portsIPL T CR48 Communication and Control Accessing and using the Web server Logon and system statusCommunication with the Interface Web serverCommunication and Control, cont’d Establishing or changing system or port settingsSetting and changing your passwords Web server port settings screenEditing and adding e-mail alerts Web server passwords screenSending an e-mail alert through Telnet Email alerts screenManaging files Upgrading the firmwareWeb server File Management screen Using the command/response table Symbol definitions 10- ASCII-to-HEX conversion table= Nvram Communication and ControlCopyright 2003, Extron Electronics IPL T CR48 Copyright informationError responses Password informationRelay functions Input Contact Closure portFirmware Version/Part Number/Information IPL T CR48 IP Setup CommandszCommand Ascii Telnet URL Encoded Web Response ControlIPL T CR48 Communication EDH ECA Re-map port designations File CommandsMail Web Browser SpecificEvent Control ECMEAE Reset ZAP/Erase CommandsTelnet port Accessing and using TelnetCommunication and Control, cont’d Device Control Custom Web pagesPower connections TroubleshootingData connections ConfigurationAAppendix a Specifications Specifications, Part Numbers, AccessoriesCE, CUL, UL IPL T CR48 Specifications, Part Numbers, and AccessoriesIncluded parts AccessoriesIncluded parts Replacement Part number Accessories Part numberAppendixBB Glossary GlossaryIPL T CR48 Glossary IPL T CR48 Glossary Glossary, cont’d USA, Canada, South America Japan Central America Extron’s WarrantyExtron Electronics. All rights reserved
Related manuals
Manual 46 pages 9.65 Kb

IPL T CR48 specifications

The Extron IPL T CR48 is a cutting-edge technology solution designed for modern audiovisual environments. As a compact, high-performance control processor, it is specifically tailored for managing and automating AV systems in various settings, including classrooms, conference rooms, and other collaborative spaces. The IPL T CR48 seamlessly integrates with a wide range of Extron products and third-party devices, making it a versatile choice for any AV installation.

One of the main features of the IPL T CR48 is its powerful control capabilities. It supports up to 48 programmable control ports, which allow users to manage multiple displays, projectors, and other audiovisual equipment effortlessly. This extensive control range ensures that every device in the AV system is easily operable from a single interface, streamlining the user experience.

In addition to its impressive control capabilities, the IPL T CR48 integrates advanced IPLink technology. This unique feature allows for remote control and monitoring of AV systems over an IP network, offering system administrators the flexibility to manage equipment from virtually anywhere. This capability is particularly valuable in large installations, where managing multiple systems simultaneously can be complex and time-consuming.

The IPL T CR48 also boasts a user-friendly interface, thanks to its compatibility with Extron's GlobalViewer Enterprise software. This robust software provides users with a web-based platform for real-time monitoring and management of their AV systems. It enables users to configure, schedule, and control their AV devices, ensuring a smooth operation throughout all events and presentations.

Moreover, the IPL T CR48 is engineered with enhanced security features, including customizable user access levels, ensuring that only authorized personnel can control sensitive equipment. This aspect is crucial for educational and corporate environments, where security and privacy are paramount.

Compact and reliable, the IPL T CR48 excels in both functionality and performance. Its durable design and advanced technologies make it a preferred choice among AV professionals looking to improve the efficiency of their installations. Overall, the Extron IPL T CR48 represents a significant advancement in control processing technology, providing a comprehensive solution for diverse audiovisual applications today.
Top Page Image Contents