Extron electronic MVX VGA A manual Configuration worksheet, Preset #

Page 68

Input sources

MVX VGA A Matrix Switchers

1

1

2

2

3

3

4

4

5

5

6

6

7

7

8

8

9

9

10

10

11

11

12

12

13

13

14

14

15

15

16

16

• Operation 3-45

Output destinations

Preset #

 

Title:

 

Video:

 

Audio:

 

Fill in the preset number and use colors, dashes, etc., to make connecting lines.

Indicate if the configuration is for video, audio, or both.

Configuration worksheet

PRELIMINARY

Image 68
Contents Computer Video VGA and Audio Matrix Switchers MVX VGA aSafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolFCC Class a Notice Input and output buttons select inputs Preset button selectsMVX VGA a Matrix Switchers Quick Start QS-1 Saving or recalling a preset Viewing and adjusting the audio levelQS-2 MVX VGA a Matrix Switchers Quick Start Creating a tieTable of Contents Table of Contents, cont’d Appendix a Specifications, Part Numbers, Accessories MVX VGA a Matrix Switchers Table of Contents IiiIv MVX VGA a Matrix Switchers Table of Contents One About this Manual About the MVX VGA a Matrix SwitchersMVX VGA a Matrix Switchers Introduction Definitions Features Tie any input to any or all outputsPreliminary Preliminary Two Mounting the Switcher MVX VGA a Matrix Switchers InstallationUL requirements Mounting instructionsRear Panel Cabling and Views Computer OUTSync Impedance switches Video connectionsAudio connections OhmsRS-232/RS-422 connection Connections for balanced and unbalanced audio outputs TheseReset button Power connectionFront Panel Configuration Port Be used for this connectionThree Definitions Front Panel Controls and IndicatorsMVX VGA a Matrix Switchers Operation Input and output buttons Sample labelOperation, cont’d Control buttonsPreliminary Controls Front panel security lockouts PowerFront Panel Operations Creating a configuration Example 1 Creating a set of video and audio ties Press and release the Esc button figureSelect the outputs Press and release the Output 1 button figure Example 2 Adding a tie to a set of video and audio tiesPress and release the Input 5 button figure 13 Press the Enter button Example 3 Removing a tie from a set of video and audio ties 15 Clear all selectionsPress and release the Output 4 button figure Press and release the Enter button figureViewing a configuration 21 Clear all selectionsPreliminary Rgbhv button and the Audio button figure24 Deselect Rgbhv to view audio ties only Muting and unmuting video and/or audio Example 5 Muting and unmuting an output28 Select Rgbhv and audio 30 Unmute the outputs Using global presets 32 Preset locations, MVX 128 VGA aExample 6 Saving a preset LED blinks figureExample 7 Recalling a preset Press and release the Preset button figure40 Select the preset Viewing and adjusting the input audio level 42 Audio gain and attenuationExample 8 Viewing and adjusting an input audio level 43 Clear all selectionsPreliminary 45 Select an input and read the audio level 47 Adjust the input audio level Viewing and adjusting the output volume Reading the displayed volume Audio output volume settings Example 9 Viewing and adjusting an output volume level 50 Clear all selections52 Select output 54 Adjust the output audio volume Setting the front panel locks Executive modes Selecting Lock mode 2 or toggling between mode 2 and modePerforming a system reset from the front panel System reset does not replace user-installed firmwareSelecting the rear panel Remote port protocol and baud rate Release the Control buttons61 RS-232/RS-422 and baud rate selection Performing an absolute system reset from the rear panel Rear Panel OperationsPerforming a hard reset from the rear panel Optimizing the AudioWorksheet example 1 System equipment TroubleshootingConfiguration Worksheets Worksheet example 2 Daily configuration 66 Worksheet example 2 Daily configurationWorksheet example 3 Test configuration PreliminaryConfiguration worksheet Preset #Preliminary Four Rear panel Remote port MVX VGA a Matrix Switchers Programmer’s GuideSerial Ports Front panel Configuration port Host-to-Switcher InstructionsSwitcher-Initiated Messages Switcher Error Responses Using the Command/Response TableCommand/Response Table for SIS Commands Symbol definitionsCommand Ascii command Response Additional Description% G InX! AudX$ Preliminary Exng EZG EX1$ *X1% ,X1 ,X1& ,X1* CP CpnX1$ CcpX1% ,X1 ,X1& ,X1 VX2XX2!AX2XX2 Five MVX VGA a Matrix Switchers Matrix Software Matrix Switchers Control ProgramInstalling the software Using the Matrix Switcher Control software Comm port selection windowMatrix Software, cont’d Sample program window complete Location of firmware upgrade files Updating firmwareDownloading firmware upgrade files Open window Firmware Loader status indicator bar File menu Windows buttons, drop boxes, and trash canWindows menus Tools menu 10 Status windowMaster-Reset selection Preferences menuButton-Label Generator Program Using Emulation modeUsing the help system Using the Button-Label Generator software 14 Extron’s Button-Label Generator windowAppendixAA Specifications, Part Numbers, Accessories SpecificationsSync Specifications, Part Numbers, Accessories, cont’d Part Numbers and Accessories MVX matrix switcher part numbersAccessories Included partsMale-to-female VGA molded connector cables Part number Male-to-female VGA backshell connector cables Part numberMale-to-male VGA molded connector cables Part number CablesPreliminary Button Labels Preliminary Preliminary Extron’s Warranty Asia JapanExtron Electronics, Europe Beeldschermweg 6C
Related manuals
Manual 19 pages 43.08 Kb