Extron electronic MVX VGA A manual Sync

Page 98

Sync

Input type

RGBHV, RGBS, RGsB, RsGsBs

Output type

RGBHV, RGBS, RGsB, RsGsBs (follows input)

Input level

0.5 V to 5.0 Vp-p, 4.0 Vp-p normal

Output level

AGC to TTL: 4.0 V to 5.0 Vp-p, unterminated

Input impedance

510 ohms

Output impedance

 

MVX 128 A

75 ohms

All other models

Inputs 1 to 8: 50 or 75 ohms, switchable

 

Inputs 9 to 12 or 16: 75 ohms

Max input voltage

5.0 Vp-p

Max. propagation delay

<120 ns

Max. rise/fall time

11.5 ns

Polarity

Positive or negative (follows input)

Audio — audio models only

Routing

 

128 series

12 x 8 matrix

1212 Series

12 x 12 stereo matrix

168 Series

16 x 8 stereo matrix

1616 Series

16 x 16 stereo matrix

Gain

Unbalanced output: -6 dB; balanced output 0 dB

Frequency response

20 Hz to 20 kHz, ±0.05 dB

THD + Noise

0.03% @ 1 kHz at nominal level

S/N

>90 dB, balanced, at maximum output (21 dBu) (unweighted)

Crosstalk

<-80 dB @ 1 kHz, fully loaded

Stereo channel separation

>80 dB @ 1 kHz

CMRR

>75 dB @ 20 Hz to 20 kHz

Audio input — audio models only

Number/signal type

12 or 16 stereo, balanced/unbalanced

Connectors

(12 or 16) 3.5 mm captive screw connectors, 5 pole

Impedance

>10k ohm, balanced/unbalanced, DC coupled

Nominal level

-10 dBV (316 mVrms), 0 dBu (775 mV)

Maximum level

+19.5 dBu, (balanced or unbalanced) at 0.01% THD+N

Input gain adjustment

-18 dB to +24 dB (default = 0 dB), adjustable per input by RS-232/422 or

 

front panel

N0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu

Audio output — audio models only

Number/signal type

8, 12, or 16 stereo, balanced/unbalanced

Connectors

(8, 12, or 16) 3.5 mm captive screw connectors, 5 pole

Impedance

50 ohms unbalanced, 100 ohms balanced

Gain error

±0.1 dB channel to channel

Maximum level (Hi-Z)

>+21 dBu, balanced or unbalanced at 0.1% THD+N

Maximum level (600 ohm)

>+15 dBm, balanced or unbalanced at 0.1% THD+N

Output volume range

0 to 64 (-75.8 dB to 0 dB) in 1 dB increments from steps 1 to 64,

 

12 dB increment from step 0 to 1; default = 64 = 0 dB

PRELIMINARY

MVX VGA A Matrix Switchers • Specifications, Part Numbers, Accessories A-3

Image 98
Contents Computer Video VGA and Audio Matrix Switchers MVX VGA aSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolFCC Class a Notice Input and output buttons select inputs Preset button selectsMVX VGA a Matrix Switchers Quick Start QS-1 QS-2 MVX VGA a Matrix Switchers Quick Start Saving or recalling a presetViewing and adjusting the audio level Creating a tieTable of Contents Table of Contents, cont’d Appendix a Specifications, Part Numbers, Accessories MVX VGA a Matrix Switchers Table of Contents IiiIv MVX VGA a Matrix Switchers Table of Contents One About this Manual About the MVX VGA a Matrix SwitchersMVX VGA a Matrix Switchers Introduction Definitions Features Tie any input to any or all outputsPreliminary Preliminary Two UL requirements Mounting the SwitcherMVX VGA a Matrix Switchers Installation Mounting instructionsRear Panel Cabling and Views Computer OUTSync Impedance switches Video connectionsAudio connections OhmsRS-232/RS-422 connection Connections for balanced and unbalanced audio outputs TheseReset button Power connectionFront Panel Configuration Port Be used for this connectionThree Definitions Front Panel Controls and IndicatorsMVX VGA a Matrix Switchers Operation Input and output buttons Sample labelOperation, cont’d Control buttonsPreliminary Controls Front panel security lockouts PowerFront Panel Operations Creating a configuration Example 1 Creating a set of video and audio ties Press and release the Esc button figureSelect the outputs Press and release the Output 1 button figure Example 2 Adding a tie to a set of video and audio tiesPress and release the Input 5 button figure 13 Press the Enter button Example 3 Removing a tie from a set of video and audio ties 15 Clear all selectionsPress and release the Output 4 button figure Press and release the Enter button figureViewing a configuration 21 Clear all selectionsPreliminary Rgbhv button and the Audio button figure24 Deselect Rgbhv to view audio ties only Muting and unmuting video and/or audio Example 5 Muting and unmuting an output28 Select Rgbhv and audio 30 Unmute the outputs Using global presets 32 Preset locations, MVX 128 VGA aExample 6 Saving a preset LED blinks figureExample 7 Recalling a preset Press and release the Preset button figure40 Select the preset Viewing and adjusting the input audio level 42 Audio gain and attenuationExample 8 Viewing and adjusting an input audio level 43 Clear all selectionsPreliminary 45 Select an input and read the audio level 47 Adjust the input audio level Viewing and adjusting the output volume Reading the displayed volume Audio output volume settings Example 9 Viewing and adjusting an output volume level 50 Clear all selections52 Select output 54 Adjust the output audio volume Setting the front panel locks Executive modes Selecting Lock mode 2 or toggling between mode 2 and modePerforming a system reset from the front panel System reset does not replace user-installed firmwareSelecting the rear panel Remote port protocol and baud rate Release the Control buttons61 RS-232/RS-422 and baud rate selection Performing an absolute system reset from the rear panel Rear Panel OperationsPerforming a hard reset from the rear panel Optimizing the AudioWorksheet example 1 System equipment TroubleshootingConfiguration Worksheets Worksheet example 2 Daily configuration 66 Worksheet example 2 Daily configurationWorksheet example 3 Test configuration PreliminaryConfiguration worksheet Preset #Preliminary Four Rear panel Remote port MVX VGA a Matrix Switchers Programmer’s GuideSerial Ports Front panel Configuration port Host-to-Switcher InstructionsSwitcher-Initiated Messages Switcher Error Responses Using the Command/Response TableCommand/Response Table for SIS Commands Symbol definitionsCommand Ascii command Response Additional Description% G InX! AudX$ Preliminary Exng EZG EX1$ *X1% ,X1 ,X1& ,X1* CP CpnX1$ CcpX1% ,X1 ,X1& ,X1 VX2XX2!AX2XX2 Five MVX VGA a Matrix Switchers Matrix Software Matrix Switchers Control ProgramInstalling the software Using the Matrix Switcher Control software Comm port selection windowMatrix Software, cont’d Sample program window complete Location of firmware upgrade files Updating firmwareDownloading firmware upgrade files Open window Firmware Loader status indicator bar File menu Windows buttons, drop boxes, and trash canWindows menus Tools menu 10 Status windowMaster-Reset selection Preferences menuButton-Label Generator Program Using Emulation modeUsing the help system Using the Button-Label Generator software 14 Extron’s Button-Label Generator windowAppendixAA Specifications, Part Numbers, Accessories SpecificationsSync Specifications, Part Numbers, Accessories, cont’d Accessories Part Numbers and AccessoriesMVX matrix switcher part numbers Included partsMale-to-male VGA molded connector cables Part number Male-to-female VGA molded connector cables Part numberMale-to-female VGA backshell connector cables Part number CablesPreliminary Button Labels Preliminary Preliminary Extron’s Warranty Asia JapanExtron Electronics, Europe Beeldschermweg 6C
Related manuals
Manual 19 pages 43.08 Kb