Command | ASCII command | Response | Additional description |
| (host to switcher) | (switcher to host) |
|
Refer also to the MTPX Plus
MTPX Plus Series • Remote
Input signal level and peaking and auto calibrate
Set input signal level | EX!*X^Ipek} |
Increment input peaking | EX!+Ipek} |
Decrement input peaking | |
Read input peaking setting | EX!Ipek} |
Execute auto calibration | EX!*0AADJ} |
IpekX!*X^]
IpekX!*X^]
IpekX!*X^]
X^]
AadjX!*2] {start} Qik] {tie creation} AadjX!*X&] {finished} IpekX!*X^] {new value}
Set a specific
Increase the input
Tie input X! to output 1 and auto adjust the peaking on input X!. The X& value in the response reports whether the adjustment value was within or outside of the threshold.
User’s Manual at www.extron.com.
Control and Optimizing
NBefore issuing the auto calibration command:
1. Disconnect the power and
2. Connect the two cables to the included MTP signal generator.
3. If the input cable is longer than 300 feet (90 m), place the
NThe MTP signal generator does not work on cable lengths over 400 feet (120 m). Set the level and peaking to its maximum value of 255.
Refer also to the MTPX Plus User’s Manual at www.extron.com.
the Video
MTPX Plus Series • Remote Control and Optimizing the Video 4-7
N X!= Input number | 01 – (maximum number of inputs for your model) | |
X^= Input signal level/peaking range | 000 – 255 | |
X&= Threshold | 0 | = outside of threshold |
| 1 | = within threshold |
Command | ASCII command | Response | Additional description |
| (host to switcher) | (switcher to host) |
|
Input skew adjustment
NFor the MTPX Plus, these commands apply to inputs 5 through 12 only.
Set all input skew adjustment | EX!*X**X**X*Iseq} | IseqX!*X**X**X*] | Set a specific skew adjustment for the TP |
values |
|
| input. X* values are listed in RGB order. |
Example: | E2*0*0*4Iseq} | Iseq02*0*0*4] | Set the skew settings for input 2 as follows: |
|
|
| Red = 0 ns |
|
|
| Green = 0 ns |
|
|
| Blue = 8 ns (delayed 8 ns) |
Increment one input skew | EX!*X(+Iseq} | IseqX!*X**X**X*] | Increase the X( skew plane adjustment for |
adjustment value |
|
| input X! by 1 step (2 ns). |
Example: | E2*2*+Iseq} | Iseq02*0*0*5] | Increase the blue skew input for 2 by 2 ns |
|
|
| (from 8 ns to 10 ns). |
Decrement one input skew |
| IseqX!*X**X**X*] | Decrease the X( skew plane adjustment for |
adjustment value |
|
| input X! by 1 step (2 ns). |
Read input skew adjustment | EX!Iseq} | X**X**X*] |
|
values |
|
|
|
|
| ||
N X!= Input number | 01 – (maximum number of TP inputs for your model) | ||
X*= Skew adjustment range | 00 – 31 (each step = 2 ns) |
| |
X(= Video plane | 0 = red |
|
|
1 = green
2 = blue