Extron electronic MTPX PLUS 128 First-time connection considerations, Starting the program

Page 24

Remote Control and Optimizing the Video, cont’d

4. Follow the on-screen instructions. The installation program creates a C:\Program Files\Extron\ Matrix_Switchers directory and an “Extron Electronics\ Matrix Switchers” group folder. It installs the following four programs:

MATRIX Switcher+ Control Program

MATRIX Switcher+ Help

Uninstall MATRIX Switcher

Check for Matrix Updates

First-time connection considerations

LAN port connection

If you connect your PC to the switcher via the LAN port, and it is the first time you have done so, you may change the default settings (IP address, subnet mask, and [optional] administrator name and password) on the controller. See "Configuring for Network Communication" on page 4-24 for details.

USB port connection

If you connect your PC to the MTPX Plus 128 via the USB port, and it is the first time you have done so, the Found New Hardware Wizard appears.

1

1

Activate the connected USB port for your device as follows:

NIf you have not installed the latest Matrix Switchers Control Program, click Cancel and install the program. Reconnect the switcher to the Configuration port.

1.

Select the No, not this time radio button and click Next.

 

The wizard installs the necessary driver to access the

 

switcher via the Configuration (USB) port (this may take a

 

few minutes).

2.

On the next page that appears, select the Install the

 

software automatically radio button and click Next.

 

Follow the on-screen instructions. The wizard assigns the

 

driver necessary to access the switcher to the connected

 

Configuration (USB) port (this may take a few minutes).

3.

Click Finish to exit the wizard.

NYou may need to repeat these steps if you subsequently connect the switcher to a different USB port on the same computer.

Starting the program

1.Click Start > Programs > Extron Electronics > Matrix Switchers > MATRIX Switcher + Control Pgm.

The Comm Port Selection window appears.

4-16 MTPX Plus Series • Remote Control and Optimizing the Video

MTPX Plus Series • Remote Control and Optimizing the Video 4-17

Refer also to the MTPX Plus User’s Manual at www.extron.com.

Refer also to the MTPX Plus User’s Manual at www.extron.com.

Image 24
Contents Setup Guide Mini Twisted Pair Matrix SwitchersPrecautions Extron Warranty安全须知 中文 FCC Class a NoticeTable of Contents Mtpx Plus Series Matrix Switcher Table of Contents, cont’dAbout the Mtpx Plus Switchers IntroductionAbout this Manual Extron Mtpx PlusTP Skew Equalization VideoFormat Two Introduction, cont’dInstallation Mtpx Plus Series InstalllationRear Panel InputsInstallation, cont’d Remote controlRS-232 output inserts OutputsPower Configuration port switchers other than the Mtpx PlusFront Panel Saving or Recalling a Preset Front Panel OperationCreating a Tie Mtpx Plus Series Front Panel OperationSelecting Lock mode 2 or toggling between mode 2 and mode Mtpx Plus Series Front Panel OperationViewing and Adjusting the Audio Level Configuration for that inputVideo Adjustments Front Panel Operation, cont’dViewing Ties and Muting Outputs Remote Control and Optimizing the Video Selected SIS CommandsHost-to-switcher instructions Establishing a network Ethernet connectionRemote Control and Optimizing the Video, cont’d Command/response table for selected SIS commandsMtpx Plus Series Remote Control and Optimizing the Video Command Ascii command Response Additional descriptionEX! *X Ipek EX! IpekEX!*X**X**X*Iseq IseqX!*X**X**X EX!*X+Iseq IseqX!*X**X**XEX@ *X +Oseq EX@ *X -OseqEX@ Oseq EX1OpekRemote Control and Optimizing the Video, cont’d @*X1V @+V@-V SprX2IP setup WwwInstalling and Starting the Control Program Installing the programFirst-time connection considerations Starting the programLAN port connection USB port connectionIs the factory-specified default value for this field Optimizing the videoManually setting the Mtpx level and peaking Setting Mtpx skewAccessing the Html Pages Setting MTP Receiver level/peakingMtpx Plus Series Remote Control and Optimizing the Video Selecting Mtpx Plus Pre-PeakConfiguring for Network Communication Loading the start-upStart the Web browser program Remote Control and Optimizing the Video, cont’d