Extron electronic MTPX PLUS 1632 Selecting Lock mode 2 or toggling between mode 2 and mode

Page 13

Front Panel Operation, cont’d

Setting the Front Panel Locks (Executive Modes)

The matrix switcher has three levels of front panel security lock that limit the operation of the switcher from the front panel. The three levels are:

•Lock mode 0 — The front panel is completely unlocked.

•Lock mode 1 — All changes are locked from the front panel (except for setting Lock mode 2). Some functions can be viewed.

•Lock mode 2 — Basic functions are unlocked. Advanced functions are locked and can be viewed only.

Basic functions consist of:

m Making ties

m Saving and recalling presets

m Setting input audio gain and attenuation m Changing Lock modes

Advanced functions consist of:

m Setting audio output mutes m Setting audio output volume

m Setting audio/RS-232 wire pair and front panel configuration

NThe switcher is shipped from the factory in Lock mode 2.

Selecting Lock mode 2 or toggling between mode 2 and mode 0

NIf the switcher is in Lock mode 0 or mode 1, this procedure selects mode 2.

If the switcher is in Lock mode 2, this procedure selects mode 0 (unlocks the switcher).

Toggle the lock on and off by pressing and holding the Enter button, the Video button, and the Audio button simultaneously for approximately 2 seconds.

Press and hold simultaneously.

	I / O
ENTER	VIDEO AUDIO

2 seconds

I / O

	ENTER	VIDEO AUDIO
	The buttons blink twice.		= lit,	= blinking,
	Release the buttons.		= lit,	= blinking,
	Release the buttons.
3-4	MTPX Plus Series • Front Panel Operation

Selecting Lock mode 2 or toggling between mode 2 and mode 1

NIf the switcher is in Lock mode 0 or mode 1, this procedure selects mode 2.

If the switcher is in Lock mode 2, this procedure selects mode 1.

Toggle the lock on and off by pressing and holding the Video button and the Audio button simultaneously for approximately 2 seconds.

Press and hold simultaneously.

I / O

VIDEO AUDIO

2 seconds

I / O

VIDEO AUDIO

The buttons blink twice.

Release the buttons.

= lit, = blinking,

MTPX Plus Series • Front Panel Operation

3-5

Refer also to the MTPX Plus User’s Manual at www.extron.com.

Refer also to the MTPX Plus User’s Manual at www.extron.com.

Image 13

Contents Mini Twisted Pair Matrix Switchers Setup GuideExtron Warranty PrecautionsFCC Class a Notice 安全须知中文Table of Contents Table of Contents, cont’d Mtpx Plus Series Matrix SwitcherIntroduction About the Mtpx Plus SwitchersAbout this Manual Extron Mtpx PlusVideo TP Skew EqualizationFormat Introduction, cont’d TwoMtpx Plus Series Installlation InstallationRear Panel InputsRemote control Installation, cont’dRS-232 output inserts OutputsConfiguration port switchers other than the Mtpx Plus PowerFront Panel Front Panel Operation Saving or Recalling a PresetCreating a Tie Mtpx Plus Series Front Panel OperationMtpx Plus Series Front Panel Operation Selecting Lock mode 2 or toggling between mode 2 and modeConfiguration for that input Viewing and Adjusting the Audio LevelFront Panel Operation, cont’d Video AdjustmentsViewing Ties and Muting Outputs Selected SIS Commands Remote Control and Optimizing the VideoHost-to-switcher instructions Establishing a network Ethernet connectionCommand/response table for selected SIS commands Remote Control and Optimizing the Video, cont’dMtpx Plus Series Remote Control and Optimizing the Video Command Ascii command Response Additional descriptionEX! Ipek EX! *X IpekEX!*X**X**X*Iseq IseqX!*X**X**X EX!*X+Iseq IseqX!*X**X**XEX@ *X -Oseq EX@ *X +OseqEX@ Oseq EX1OpekRemote Control and Optimizing the Video, cont’d @+V @*X1V@-V SprX2Www IP setupInstalling the program Installing and Starting the Control ProgramStarting the program First-time connection considerationsLAN port connection USB port connectionOptimizing the video Is the factory-specified default value for this fieldSetting Mtpx skew Manually setting the Mtpx level and peakingSetting MTP Receiver level/peaking Accessing the Html PagesMtpx Plus Series Remote Control and Optimizing the Video Selecting Mtpx Plus Pre-PeakLoading the start-up Configuring for Network CommunicationStart the Web browser program Remote Control and Optimizing the Video, cont’d