Extron electronic 3200s manual Control Software, cont’d, Igure 3-3.A

Page 24

Control Software, cont’d

FIGURE 3-2.A

The program will communicate with the Matrix 3200/6400 System to determine its hardware configuration (type and size of each connected BME). It then reads the system’s settings (Ties, Presets, Virtual Map, etc.) and draws a graphical representation of the unit’s configuration and settings (Ties) on the Main screen (Figure 3-5.A & B). It also reads the MTRX6400.INI file (saved from last session) to draw Icons for each I/O (if any had been applied in previous programming sessions) to make the graphical representation even more friendly.

If this is a new system that has not been virtualized yet or one that has had its map cleared, the graphical representation and all information shown on the Virtual Map screen may be invalid at this time.

From the menu on the Main screen, click

SYSTEM- CONFIG to show the Virtual Map

screen (see

 

Figure 3-

 

4.A). From

 

the Virtual

FIGURE 3-3.A

Map screen

menu, click CONFIGUREPHYSICAL SWITCHERS to show the Physical Configuration screen (Figure 3-3.A). Examine this screen to ensure that all BMEs were seen and their type and size is being reported as expected. Click on the ‘Close’ button to return to the Virtual Map screen.

From the Virtual Map screen menu, click CONFIGUREVIRTUAL SWITCHER to show the Virtual Configuration screen. This screen shows how the physical system will be mapped into a virtual system switcher by the Windows program (see Figure 3-4.B). You may need to make some choices at this time that affect how many virtual planes will be created and how many virtual inputs and outputs will exist. For example, if a Sync BME was found, the program needs you to decide whether to use composite sync (1 plane) or separate H and V sync (2 planes).

You need to decide how you want the initial map assignments organized, whether as ‘Repeat-Pattern’ (e.g. RGBRGB..B) or ‘Group-by-Plane’ (e.g.

3-4 Matrix 3200/6400 Series Control Software

Image 24
Contents Audio Switcher Matrix 3200 and 6400 SeriesSafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start Matrix 3200/6400 Series Matrix 3200/6400 Series Quick Start QS-1Quick Start Matrix 3200/6400 Series, cont’d Matrix 3200/6400 Series Quick StartTable of Contents Table of Contents, cont’d One What is a Matrix 6400 Audio Switcher? FeaturesIntroductiontroduction, cont’d Matrix 3200/6400 Series IntroductionFeature Descriptions Inputs OutputsMatrix 6400 Audio Switcher Specifications Introduction, cont’dMatrix 3200/6400 System Manuals Audio input audio BME Introduction, cont’d Two Matrix 6400 Audio Switcher Installation Installing the Matrix 6400 Audio BMEMatrix 3200/6400 Series Installation Introductionstallation, cont’dSetting BME Addresses Connecting the BME Comm interconnecting cablesInstallation, cont’d Connecting the RS-232/RS-422 Cable to BME #0Connecting the AC Power Cables to the BMEs Applying AC Power to the BMEsVirtualizing the Matrix 3200/6400 Switcher/System Using the Audio Captive Screw ConnectorsMatrix 6400 Audio Input/Output Cabling A Matrix 6400 Audio Switcher Stereo backplane D Align the stereo audio connectors before plugging them Installation, cont’d Three ControlSoftware,cont’d Matrix 3200/6400 Series Control SoftwareMatrix 3200/6400 Series Control Software Control Software, cont’d Igure 3-3.AMatrix 3200/6400 Series Control Software A Main Screen Ties How to Create Rooms within the Matrix 3200/6400 System Igure 3-7.A Matrix 3200/6400 Series Control Software How to Program the Matrix 3200/6400 System in Emulate Mode How to Save and Restore the Matrix 3200/6400 Settings 10.A Four Programmer’ser’sGuide,Guidecont’d Serial Communications PortMatrix 3200/6400 Series Programmer’s Guide Host to Switcher Communications Command/Response TableCOMMAND/RESPONSE Table Programmer’s Guide, cont’dROOM# Name Virtual Outputs VIRT-OUT# Name LVL1 LVL2 LVL6 Vmutamut ØVI Read RGB Delay for 1 ch Out Dly Set RGB Delay for 1 ch Quick Recall Preset Rpr Switcher Generated Unsolicited Responses Five UpgradesandandTroubleshooting,co t’d Upgrade and Troubleshooting ProceduresMatrix 3200/6400 Series Upgrades and Troubleshooting Adding a Front Panel Controller to an existing systemMatrix 6400 Audio BME Internal Access Upgrades and Troubleshooting, cont’d Installing a Software UpdateRibbon Cable Connectors Swapping BME #0 RS-232 / RS-422 PortsSwapping Serial Ports RS-232/RS-422 Troubleshooting a Matrix 3200/6400 System Problem Power SuppliesCommunications System StatusPrimary Matrix 6400 Audio Switcher Upgrade Changing the Matrix Size A Inserting an audio card into slotDetermining Audio Switcher Circuit Card Population Changing the Audio Output Card Gain Jumpers A Audio output card gain jumpersAdding BMEs to a Matrix 3200/6400 System Adding a Matrix 6400 Audio BMESoftware Procedure Before and After a Hardware Upgrade Upgrade System Software ProcedureBefore Hardware Changes After Hardware Changes Upgrades and Troubleshooting, cont’d Reference Information AAppendix aReferenceInformation,c t’d Matrix 3200/6400 Series Part NumbersMatrix 3200/6400 Series Reference Information Extron Part Matrix 6400 Wideband Switcher Iofr Matrix 3200/6400 Series Part Numbers from previousBNC Cables Super High Resolution SHR BNC Cables Reference Information, cont’dMatrix 3200/6400 Series Part Numbers Related Part NumbersBinary/Hex/Decimal Conversion Table Pre-cut CablesGlossary of terms Matrix 3200/6400 Series Reference Information Reference Information, cont’d PCB Printed Circuit Board Reference Information, cont’d Virtual conference room See videoconferencing Matrix 3200/6400 Series Reference Information A-11Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA