Extron electronic 3200s Introductionstallation, cont’d, Matrix 6400 Audio Switcher Installation

Page 14

Introductionstallation, cont’d

Matrix 6400 Audio Switcher Installation

Extron recommends that the following steps be done in the order listed to install a Matrix 6400 Audio BME.

1.Installing the Matrix 6400 Audio BME. (Page 2-2)

2.Set the BME address numbers (0 - 5). (Page 2-3)

3.Connect the BME COMM interconnecting cable(s). (Page 2-3)

4.Connect the RS-232/RS-422 cable to BME #0’s serial port. (Page 2-3)

5.Connect the AC Power cable(s) to the BME(s). (Page 2-3)

6.Apply AC power to the BMEs and Verify Normal Power-Up. (Page 2-3)

7.Load the Matrix 1000 System Virtualization/ Control Software. (Page 2-4)

8.Virtualize the Matrix 3200/6400 switcher/ system if required. (Page 3-2)

9.Matrix 6400 Audio Input/Output Cabling. (Page 2-5)

The numbered procedures that follow match the steps above.

1. Installing the Matrix 6400 Audio BME

The Matrix 6400 Audio BME may be a stand- alone audio switcher or it may be part of a Matrix 6400/3200 System. In either case it may be installed in a rack. If it is part of a Matrix 6400/ 3200 System, BMEs may be separated by up to 12 feet and rack mounting is NOT required. If the BMEs are to be rack mounted, they may mounted in any order within a rack or cabinet. The limiting factor is the BME COMM interconnecting cable length which is 12 feet maximum. There are no restrictions to the order in which BMEs may be mounted relative to each other. Logically, the BME addresses in a system such as the one shown in Figure 2-1.A (with Matrix 6400 Audio BME at top) would be set to 0 - 5 sequentially from top to bottom, however, a different order is acceptable and will not impact system operation in any way.

The location of the equipment within a room should be given careful consideration. Poor planning, with the number of cables involved, could result in a cluttered appearance. Power requirements and the amount of heat exhaust from the system should be taken into consideration.

FPC-1000

MATRIX 6400

AUDIO

MATRIX 6400

WIDEBAND VIDEO

MATRIX 6400

WIDEBAND VIDEO

MATRIX 6400

WIDEBAND VIDEO

MATRIX 6400

SYNC

MATRIX 6400

SYNC

Figure 2-1.A Rack-mounted Matrix 6400/3200 System w/audio

2-2 Matrix 3200/6400 Series • Installation

Image 14
Contents Audio Switcher Matrix 3200 and 6400 SeriesSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start Matrix 3200/6400 Series Matrix 3200/6400 Series Quick Start QS-1Quick Start Matrix 3200/6400 Series, cont’d Matrix 3200/6400 Series Quick StartTable of Contents Table of Contents, cont’d One Introductiontroduction, cont’d What is a Matrix 6400 Audio Switcher?Features Matrix 3200/6400 Series IntroductionFeature Descriptions Inputs OutputsMatrix 3200/6400 System Manuals Matrix 6400 Audio Switcher SpecificationsIntroduction, cont’d Audio input audio BME Introduction, cont’d Two Matrix 3200/6400 Series Installation Matrix 6400 Audio Switcher InstallationInstalling the Matrix 6400 Audio BME Introductionstallation, cont’dSetting BME Addresses Connecting the BME Comm interconnecting cablesConnecting the AC Power Cables to the BMEs Installation, cont’dConnecting the RS-232/RS-422 Cable to BME #0 Applying AC Power to the BMEsMatrix 6400 Audio Input/Output Cabling Virtualizing the Matrix 3200/6400 Switcher/SystemUsing the Audio Captive Screw Connectors A Matrix 6400 Audio Switcher Stereo backplane D Align the stereo audio connectors before plugging them Installation, cont’d Three ControlSoftware,cont’d Matrix 3200/6400 Series Control SoftwareMatrix 3200/6400 Series Control Software Control Software, cont’d Igure 3-3.AMatrix 3200/6400 Series Control Software A Main Screen Ties How to Create Rooms within the Matrix 3200/6400 System Igure 3-7.A Matrix 3200/6400 Series Control Software How to Program the Matrix 3200/6400 System in Emulate Mode How to Save and Restore the Matrix 3200/6400 Settings 10.A Four Matrix 3200/6400 Series Programmer’s Guide Programmer’ser’sGuide,Guidecont’dSerial Communications Port Host to Switcher Communications Command/Response TableCOMMAND/RESPONSE Table Programmer’s Guide, cont’dROOM# Name Virtual Outputs VIRT-OUT# Name LVL1 LVL2 LVL6 Vmutamut ØVI Read RGB Delay for 1 ch Out Dly Set RGB Delay for 1 ch Quick Recall Preset Rpr Switcher Generated Unsolicited Responses Five Matrix 3200/6400 Series Upgrades and Troubleshooting UpgradesandandTroubleshooting,co t’dUpgrade and Troubleshooting Procedures Adding a Front Panel Controller to an existing systemMatrix 6400 Audio BME Internal Access Upgrades and Troubleshooting, cont’d Installing a Software UpdateSwapping Serial Ports RS-232/RS-422 Ribbon Cable ConnectorsSwapping BME #0 RS-232 / RS-422 Ports Communications Troubleshooting a Matrix 3200/6400 System ProblemPower Supplies System StatusPrimary Matrix 6400 Audio Switcher Upgrade Changing the Matrix Size A Inserting an audio card into slotDetermining Audio Switcher Circuit Card Population Changing the Audio Output Card Gain Jumpers A Audio output card gain jumpersAdding BMEs to a Matrix 3200/6400 System Adding a Matrix 6400 Audio BMEBefore Hardware Changes Software Procedure Before and After a Hardware UpgradeUpgrade System Software Procedure After Hardware Changes Upgrades and Troubleshooting, cont’d Reference Information AAppendix aMatrix 3200/6400 Series Reference Information ReferenceInformation,c t’dMatrix 3200/6400 Series Part Numbers Extron Part Matrix 6400 Wideband Switcher Iofr Matrix 3200/6400 Series Part Numbers from previousMatrix 3200/6400 Series Part Numbers BNC Cables Super High Resolution SHR BNC CablesReference Information, cont’d Related Part NumbersBinary/Hex/Decimal Conversion Table Pre-cut CablesGlossary of terms Matrix 3200/6400 Series Reference Information Reference Information, cont’d PCB Printed Circuit Board Reference Information, cont’d Virtual conference room See videoconferencing Matrix 3200/6400 Series Reference Information A-11Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA