Extron electronic 3200s Adding BMEs to a Matrix 3200/6400 System, Adding a Matrix 6400 Audio BME

Page 53

change the gain for output 51, pull the card for outputs 49-56, count from the top header pair which is for output 49. The target headers are H13 and H14; swapping their jumper positions will change the gain for output 51.

Gain jumpers must be changed in pairs (H9 & H10 through H23 & H24).

Do NOT change the position of the jumpers on headers 25 and 26 (H25 &

H26).

Adding BME(s) to a Matrix 3200/6400 System

Adding BME(s) to an existing Matrix 3200/6400 System involves doing most of the same steps as an initial installation. Extron recommends that the following steps be done in the order listed to add an Audio BME to an existing system.

1.See Page 5-12 “Software Procedure - Before and After a Hardware Upgrade”. Do steps under “Before Hardware Changes” before making any hardware changes.

To ignore step 1 and proceed with the hardware upgrade will require considerable system reconfiguration time. It is highly recommended that you not skip any step.

2.Remove power before proceeding. Go to “Adding a Matrix 6400 Audio BME” (see Page 5-10 below). If this is not an Audio BME add-on, go to Chapter 2.

3.Set the BME address numbers (0 - 5). (Page 2-3)

4.Connect the BME COMM interconnecting cable(s). (Page 2-3)

5.Connect the RS-232/RS-422 cable to the serial port of BME #0. (Page 2-3)

6.Connect the AC Power cable(s) to the BME(s). (Page 2-3)

7.Apply AC power to the BMEs and Verify Normal Power-Up. (Page 2-3)

8.Do the steps under “After Hardware Changes” on Page 5-13.

9.Connect cables to BMEs (video, sync and/or audio cables). (Page 2-5)

The procedure for adding an Audio BME follows.

Adding a Matrix 6400 Audio BME

The Matrix 6400 Audio BME may be installed in a rack with an existing Matrix 3200/6400 system, or it may be installed in a different location. BMEs may be separated by up to 12 feet and rack mounting is NOT required. If the Audio BME is going to be rack mounted with other BMEs, they may be mounted in any order within a rack or

FPC-1000

MATRIX 6400

AUDIO

MATRIX 6400

WIDEBAND VIDEO

MATRIX 6400

WIDEBAND VIDEO

MATRIX 6400

WIDEBAND VIDEO

MATRIX 6400

SYNC

MATRIX 6400

SYNC

Figure 5-10.A

Matrix 3200/6400 Series • Upgrades and Troubleshooting 5-11

Image 53

Contents Matrix 3200 and 6400 Series Audio SwitcherConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolMatrix 3200/6400 Series Quick Start QS-1 Quick Start Matrix 3200/6400 SeriesMatrix 3200/6400 Series Quick Start Quick Start Matrix 3200/6400 Series, cont’dTable of Contents Table of Contents, cont’d One Features What is a Matrix 6400 Audio Switcher?Introductiontroduction, cont’d Matrix 3200/6400 Series IntroductionInputs Outputs Feature DescriptionsMatrix 3200/6400 System Manuals Matrix 6400 Audio Switcher SpecificationsIntroduction, cont’d Audio input audio BME Introduction, cont’d Two Installing the Matrix 6400 Audio BME Matrix 6400 Audio Switcher InstallationMatrix 3200/6400 Series Installation Introductionstallation, cont’dConnecting the BME Comm interconnecting cables Setting BME AddressesConnecting the RS-232/RS-422 Cable to BME #0 Installation, cont’dConnecting the AC Power Cables to the BMEs Applying AC Power to the BMEsMatrix 6400 Audio Input/Output Cabling Virtualizing the Matrix 3200/6400 Switcher/SystemUsing the Audio Captive Screw Connectors A Matrix 6400 Audio Switcher Stereo backplane D Align the stereo audio connectors before plugging them Installation, cont’d Three Matrix 3200/6400 Series Control Software ControlSoftware,cont’dMatrix 3200/6400 Series Control Software Igure 3-3.A Control Software, cont’dMatrix 3200/6400 Series Control Software A Main Screen Ties How to Create Rooms within the Matrix 3200/6400 System Igure 3-7.A Matrix 3200/6400 Series Control Software How to Program the Matrix 3200/6400 System in Emulate Mode How to Save and Restore the Matrix 3200/6400 Settings 10.A Four Matrix 3200/6400 Series Programmer’s Guide Programmer’ser’sGuide,Guidecont’dSerial Communications Port Command/Response Table Host to Switcher CommunicationsProgrammer’s Guide, cont’d COMMAND/RESPONSE TableROOM# Name Virtual Outputs VIRT-OUT# Name LVL1 LVL2 LVL6 Vmutamut ØVI Read RGB Delay for 1 ch Out Dly Set RGB Delay for 1 ch Quick Recall Preset Rpr Switcher Generated Unsolicited Responses Five Upgrade and Troubleshooting Procedures UpgradesandandTroubleshooting,co t’dMatrix 3200/6400 Series Upgrades and Troubleshooting Adding a Front Panel Controller to an existing systemMatrix 6400 Audio BME Internal Access Installing a Software Update Upgrades and Troubleshooting, cont’dSwapping Serial Ports RS-232/RS-422 Ribbon Cable ConnectorsSwapping BME #0 RS-232 / RS-422 Ports Power Supplies Troubleshooting a Matrix 3200/6400 System ProblemCommunications System StatusPrimary A Inserting an audio card into slot Matrix 6400 Audio Switcher Upgrade Changing the Matrix SizeDetermining Audio Switcher Circuit Card Population A Audio output card gain jumpers Changing the Audio Output Card Gain JumpersAdding a Matrix 6400 Audio BME Adding BMEs to a Matrix 3200/6400 SystemBefore Hardware Changes Software Procedure Before and After a Hardware UpgradeUpgrade System Software Procedure After Hardware Changes Upgrades and Troubleshooting, cont’d AAppendix a Reference InformationMatrix 3200/6400 Series Reference Information ReferenceInformation,c t’dMatrix 3200/6400 Series Part Numbers Matrix 3200/6400 Series Part Numbers from previous Extron Part Matrix 6400 Wideband Switcher IofrReference Information, cont’d BNC Cables Super High Resolution SHR BNC CablesMatrix 3200/6400 Series Part Numbers Related Part NumbersPre-cut Cables Binary/Hex/Decimal Conversion TableGlossary of terms Matrix 3200/6400 Series Reference Information Reference Information, cont’d PCB Printed Circuit Board Reference Information, cont’d Matrix 3200/6400 Series Reference Information A-11 Virtual conference room See videoconferencingReference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA