Extron electronic 3200s manual Read RGB Delay for 1 ch Out Dly Set RGB Delay for 1 ch

Programmer’s Guide, cont’d

Command	Response	Description
1VI	Jims_Lecture,GrpB	Read Preset 1 breakaway information (follow versus breakaway mode)

In the 4 examples below, all Ties are read from a 32 x 32 virtual RGBA (red, green, Blue, Audio) system with Audio/Video breakaway (Grp B). In Examples 1 and 2 below (Video breakaway), only virtual plane 1 (Red) needs to be read, since virtual planes 2 and 3 (Green and Blue) are the same as virtual plane 1. Examples 3 and 4 below refer to virtual Audio breakaway with virtual plane 4 representing Audio.

Example 1 1*Ø1*Ø1VC Ø4•64•ØØ•ØØ•ØØ•ØØ•Ø3•Ø1•ØØ•ØØ•ØØ•64•ØØ•Ø1•ØØ•ØØ•Plane 1↵

Explanation: Read Preset 1 Red (plane 1) Ties of Virtual Video Inputs to Virtual Video Outputs Ø1 through 16.

Example 2 1*17*Ø1VC Ø4•64•ØØ•ØØ•ØØ•ØØ•Ø3•Ø1•ØØ•ØØ•ØØ•64•ØØ•Ø1•ØØ•ØØ•Plane 1↵

Explanation: Read Preset 1 Red (plane 1) Ties of Virtual Video Inputs to Virtual Video Outputs 17 through 32.

Example 3 1*Ø1*Ø4VC Ø4•64•ØØ•ØØ•ØØ•ØØ•Ø3•Ø1•ØØ•ØØ•ØØ•64•ØØ•Ø1•ØØ•ØØ•Plane 4↵

Explanation: Read Preset 1 Audio (plane 4) Ties of Virtual Audio Inputs to Virtual Audio Outputs Ø1 through 16.

Example 4	virtual input #4 tied to virtual output #17 no virtual input tied to virtual output #32
	1*17*Ø4VC	Ø4•64•ØØ•ØØ•ØØ•ØØ•Ø3•Ø1•ØØ•ØØ•ØØ•64•ØØ•Ø1•ØØ•ØØ•Plane			4↵
			virtual input #64 tied to virtual output #18	virtual	audio plane

Explanation: Read Preset 1 Audio (plane 4) Ties of Virtual Audio Inputs to Virtual Audio Outputs 17 through 32.

	ADVANCED INSTRUCTION SET AND SIMPLE INSTRUCTION SET COMMANDS
VIEW COMMANDS	ASCII (HOST-SWITCHER)	RESPONSE (SWITCHER-HOST)
Virtual Output MUTES	VM	1• 2• • • • • 64Mut

Notes:

1.Start output is always Ø1 for Room PRESET, because room has max. of 16 outputs assigned.

2.All “VI” values in responses are 2 numeric characters (i.e. 12 or Ø3) or “na” indicating non-existant virtual outputs.

3.In “VA” View, any outputs that do not follow show as “- -“ in response.

4.SO = “Start-Output” parameter in “Global Preset commands”.

5.Rvo - Rvo.... = Set of Virtual Outputs assigned to specified “room” (up to 16 total).

RGB DELAY COMMANDS	ASCII (HOST-SWITCHER)	RESPONSE (SWITCHER-HOST)
Read RGB Delay (for 1 ch.)	D	Out	•Dly
Set RGB Delay (for 1 ch.)	d *	Out	•Dly

Note: Where = delay in 1/2 second increments (i.e. Ø = Ø sec, 1Ø = 5.Ø sec)

DIRECT WRITE OF

GLOBAL PRESETS COMMANDS		ASCII (HOST-SWITCHER)	RESPONSE (SWITCHER-HOST)
Start Write Mode		P	Write Preset	Ready
End Write Mode		p	End Write Preset
Example		P32	Write Preset 32 Ready
	1*1!
	1*2&
	1*3%
	:
	:
	1*64$
		p	End Write Preset 32

Notes:

1.Any non-output switching or invalid command between the Start and End commands will be ignored.

2.If there is no activity for 5 seconds while in write mode, then error E17 occurs.

3.No front panel switching (Actual Switching) is allowed during the Start and End commands.

4.If an End command p command is issued with no Start command, then error E10 occurs.

4-8 Matrix 3200/6400 Series • Programmer’s Guide