Extron electronic 3200s manual After Hardware Changes

Page 55

•The current MATRIX settings will be saved in the MTRX6400.INI file.

•The Matrix 6400 Control Pgm will shut down to allow you to power down the system to make the hardware changes.

5.Return to step 2 of the applicable procedure (Page 5-8 or 5-11).

Note: The “After Hardware Changes” procedure begins on Page 5-13.

After Hardware Changes

Do the following steps AFTER the hardware upgrade has been installed:

1.From Windows open the Program Group or Folder called “Extron Electronics”.

2.Double click the “Matrix 6400 Control Pgm” icon to start the program. You will be asked to select the COMM port, or choose “Emulate” mode. After the COMM port is selected, the software looks for the matrix system, “reads” its configuration, and then displays it in a window called “Extron’s Matrix 6400 Control Program.

3.Click on TOOLS, the TOOLS menu is displayed. Click on Upgrade.

4.The “Upgrade Wizard” dialog box shown below will be displayed. The options are Yes, NO and Cancel. Click on ”Yes” (since the hardware changes have been installed at this point). The “Upgrade Wizard” does the following:

•Presents the Virtual Configuration screen so you may re-virtualize the system to match your new hardware configuration.

•Restores MATRIX settings from the MTRX6400.INI file saved before the hardware configuration was changed. All settings are restored from before, except the Map.

•You may want to assign new icons and names to any Virtual IO ports that were newly created by your upgrade after the wizard has finished. This would also be the time to update your Room Configurations if needed.

5.Verify that the system (including the new hardware) is functioning correctly. If the system is not functioning as expected, call Extron Technical Support.

The upgrade wizard also allows you to downgrade your system (remove hardware), but various Room and Preset settings may not fully restore since some of the Virtual input and output ports may no longer exist.

Matrix 3200/6400 Series • Upgrades and Troubleshooting 5-13

Image 55

Contents Matrix 3200 and 6400 Series Audio SwitcherInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschMatrix 3200/6400 Series Quick Start QS-1 Quick Start Matrix 3200/6400 SeriesMatrix 3200/6400 Series Quick Start Quick Start Matrix 3200/6400 Series, cont’dTable of Contents Table of Contents, cont’d One Matrix 3200/6400 Series Introduction What is a Matrix 6400 Audio Switcher?Features Introductiontroduction, cont’dInputs Outputs Feature DescriptionsIntroduction, cont’d Matrix 6400 Audio Switcher SpecificationsMatrix 3200/6400 System Manuals Audio input audio BME Introduction, cont’d Two Introductionstallation, cont’d Matrix 6400 Audio Switcher InstallationInstalling the Matrix 6400 Audio BME Matrix 3200/6400 Series InstallationConnecting the BME Comm interconnecting cables Setting BME AddressesApplying AC Power to the BMEs Installation, cont’dConnecting the RS-232/RS-422 Cable to BME #0 Connecting the AC Power Cables to the BMEsUsing the Audio Captive Screw Connectors Virtualizing the Matrix 3200/6400 Switcher/SystemMatrix 6400 Audio Input/Output Cabling A Matrix 6400 Audio Switcher Stereo backplane D Align the stereo audio connectors before plugging them Installation, cont’d Three Matrix 3200/6400 Series Control Software ControlSoftware,cont’dMatrix 3200/6400 Series Control Software Igure 3-3.A Control Software, cont’dMatrix 3200/6400 Series Control Software A Main Screen Ties How to Create Rooms within the Matrix 3200/6400 System Igure 3-7.A Matrix 3200/6400 Series Control Software How to Program the Matrix 3200/6400 System in Emulate Mode How to Save and Restore the Matrix 3200/6400 Settings 10.A Four Serial Communications Port Programmer’ser’sGuide,Guidecont’dMatrix 3200/6400 Series Programmer’s Guide Command/Response Table Host to Switcher CommunicationsProgrammer’s Guide, cont’d COMMAND/RESPONSE TableROOM# Name Virtual Outputs VIRT-OUT# Name LVL1 LVL2 LVL6 Vmutamut ØVI Read RGB Delay for 1 ch Out Dly Set RGB Delay for 1 ch Quick Recall Preset Rpr Switcher Generated Unsolicited Responses Five Adding a Front Panel Controller to an existing system UpgradesandandTroubleshooting,co t’dUpgrade and Troubleshooting Procedures Matrix 3200/6400 Series Upgrades and TroubleshootingMatrix 6400 Audio BME Internal Access Installing a Software Update Upgrades and Troubleshooting, cont’dSwapping BME #0 RS-232 / RS-422 Ports Ribbon Cable ConnectorsSwapping Serial Ports RS-232/RS-422 System Status Troubleshooting a Matrix 3200/6400 System ProblemPower Supplies CommunicationsPrimary A Inserting an audio card into slot Matrix 6400 Audio Switcher Upgrade Changing the Matrix SizeDetermining Audio Switcher Circuit Card Population A Audio output card gain jumpers Changing the Audio Output Card Gain JumpersAdding a Matrix 6400 Audio BME Adding BMEs to a Matrix 3200/6400 SystemUpgrade System Software Procedure Software Procedure Before and After a Hardware UpgradeBefore Hardware Changes After Hardware Changes Upgrades and Troubleshooting, cont’d AAppendix a Reference InformationMatrix 3200/6400 Series Part Numbers ReferenceInformation,c t’dMatrix 3200/6400 Series Reference Information Matrix 3200/6400 Series Part Numbers from previous Extron Part Matrix 6400 Wideband Switcher IofrRelated Part Numbers BNC Cables Super High Resolution SHR BNC CablesReference Information, cont’d Matrix 3200/6400 Series Part NumbersPre-cut Cables Binary/Hex/Decimal Conversion TableGlossary of terms Matrix 3200/6400 Series Reference Information Reference Information, cont’d PCB Printed Circuit Board Reference Information, cont’d Matrix 3200/6400 Series Reference Information A-11 Virtual conference room See videoconferencingReference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA