Extron electronic 325 manual Configuration Selections

Page 25

Configuration Selections

NOTES: • In a typical installation, you:

• Must change the address (2 or 12), netmask (3 or 13), gateway address

(4 or 14), and controller IP (7).

• May need to change the boot method (1 or 11).

• Most installers do not need to change the other selections. If you do change settings, note the existing values before the change in case you need to change back.

• Options 0 through 6 are the settings for LAN port 1 (the RJ-45 port).

• Options 10 through 16 are the settings for LAN port 3 (the optical port).

• Options 7 through 9, 17, and 18 are controller related.

• Selections marked with an asterisk (*) in options 0 and 10 below are the default VNC 325 hardware settings and the correct selection in most cases.

Table 5. Configuration Selections

LAN Port Specific Options

Option Function

Comments

0Speed/Duplex: Allows you to set the speed of the RJ-45 LAN port manually

LAN port 1 link speed using the following subselections:

*1. auto_10_100_1000

2.auto_10_100

3.fixed_1000F

4.fixed_100F

5.fixed_100H

10Speed/Duplex: Allows you to set the speed of the optical LAN port manually

LAN port 2 link speed using the following subselections: 6. fibre_auto_1000

*7. fibre_fixed_1000F

1 and 11 Boot method:

Entering 1 (11) toggles this option. When DHCP is selected

 

Set static or dhcp

items 2 (12) through 5 (15) are not accessible.

 

 

NOTE: Extron recommends that you use static IP addresses.

2 and 12

address:

• Standard Ethernet IP addressing rules apply.

 

Set the local address

• Manually enter the IP address for the port; use no leading

 

of the LAN port

 

zeroes. For example: 192.168.0.1 is valid, 192.168.000.001

 

 

 

 

is not valid.

3 and 13

netmask:

• Standard Ethernet subnet rules apply.

 

Set the appropriate

• Manually enter the IP address for the port; use no leading

 

subnet mask for the

 

zeroes. For example: 255.255.10.0 is valid, 255.255.010.0

 

network.

 

is not valid.

 

 

VN-Matrix 325 Serial Digital Over IP CODEC • Installation and Setup 19

Page 24 Page 26
Image 25
Page 24 Page 26
Contents VN-Matrix325 Safety Instructions English FCC Class a Notice Conventions Used in this Guide Contents VN-Matrix 325 Serial Digital Over IP Codec Contents About the VNC 325 Codec About this GuideVN-Matrix 325 Serial Digital Over IP Codec Introduction Configurable as encoder and decoder FeaturesTwo levels of operator interface Two RS-232 serial portsVN-Matrix 325 Serial Digital Over IP Codec Introduction Installation and Setup Overview Installation SetupVNC 325 Features Rear Panel FeaturesPlanning the System Architecture Mounting the UnitsMulticast RTP Data Transport MethodsTypical Unicast RTP Application Unicast RTPUnicast TCP Data and Control RoutingSwitched and Isolated Network Configuration Example 1 Switched and isolated network configurationApplicable Codec Configuration Selections LAN Port Example 2 Switched and isolated network configurationCodec Option LAN Port 1 RJ-45 LAN Port 2 fiber optic Routed Network Configuration Example 3 Routed Network ConfigurationSerial Port Wiring Configuring Network SettingsBaud rate Data bits Parity None Stop bits Flow control None Low-level Network Configuration Controller IP option Configuration MenuConfiguration Selections Configuration SelectionsLAN Port Specific Options Function Comments Ip forwarding Not implemented. Do not change this valueRS-232 Over LAN Port Making Remaining ConnectionsLAN Ports RJ-45 Connector and Pinout Tables RJ-45 port wiringVideo Input, Output, and Loop Connections Encoder configurationLoop BNC connector Not used Decoder configurationStartup and Login Configure Encoders and DecodersDevice List Typical VN-Matrix 325 System Configure the Units as Encoders or DecodersConfiguring a Codec as a Source or Display Enable multicast streaming Encoder Configuration Enable multicast streamingLAN-1 and LAN-2 LEDs Indications and ControlsStatus LED Network Interface Device List Device ModeDevice Field Removing a device from the networkTypical Device Page for an Encoder DeviceDevice summary panel Licensed features panelConfiguration panel Device setup panelMode Streams panel Configuration Page Video EncoderName panel Configuration Page Audio EncoderANC Audio panel Audio Encoder FEC Panel Forward error correction FEC panelAudio Encoder Streams Panel Configuration Page Colfec and Rowfec EncodersFEC Encoder Streams Panel Bandwidth Management Page and Typical Bit RatesBandwidth Management Standard Controls Panel Bandwidth management standard controls panelAdvanced Controls Panel Advanced Controls panelBandwidth Management Peak flow rate Typical Embedded Audio Bit Rates in Transparent ModeMaximum bit rates Broadcast Contribution Video BitDecoder Video Configuration Panel Decoder Display and ConfigurationDecoder Streams Configuration Panel Decoder Streams Configuration PanelDecoder Bit Rate and Stream Decoder Bit Rate and StreamRaw Network Statistics Panel Pass-through Control Peripherals Page and Serial Port ControlConfiguring a Serial Pass-through Group Configuring a Serial Pass-through GroupFirmware Upgrade Stages Function Summary Perform on Firmware UpgradeUpgrade Uploading the upgrade to the controller codecInstalling the firmware prepare, activate, and commit stages License Passwords Panel Accounts Page Passwords and Clock ManagementController Licensing Panel Clock Management PanelAlarms AlarmsAlarm Source Filter settings panelAlarm Severity Description Critical NoneAlarm types and descriptions Alarm list panelEncoder Alarm Encoder Alarm Type and Description Action Default SettingsIndicates that there is a valid Alarm Log Alarm LogsSimple Network Management Protocol Snmp Password ValueSnmp Trap Destination Values Snmp Community ValueVideo SpecificationsVideo input and loop through encoder Video processing codecAudio input and output Sync genlock decoderAudio processing Control host ports codecs, decodersGeneral Network transportMounting and Power Options Part Numbers and AccessoriesCodec Part Number and Included Parts Optional SFP ModuleTabletop Use Mounting the CodecMounting kits UL Rack-Mounting GuidelinesOutput format Test Pattern1280 x 720x480 Extron Warranty
Related manuals
Manual 4 pages 38.42 Kb

325 specifications

Extron Electronics has established itself as a key player in the AV technology industry, providing innovative solutions for a wide range of applications. Among their product lineup, the Extron Electronics 225 and 325 series of devices stand out for their advanced features, technologies, and characteristics that cater to both commercial and educational environments.

The Extron 225 and 325 series are designed for seamless integration into various AV systems, offering unparalleled performance and reliability. At the core of these devices is their robust signal processing capability. Both models are equipped with high-performance scalers and switchers that ensure optimal video quality. They support a wide range of resolutions, including 4K, enabling users to connect various sources without compromising image fidelity.

One of the key features of the 225 and 325 series is their versatile connectivity options. These devices come with multiple inputs, including HDMI, VGA, and composite, allowing for the integration of various AV sources. The series also includes configurable outputs, which can be customized according to the specific requirements of the installation. This flexibility is vital in multipurpose spaces where different AV setups are needed.

The technologies embedded in the 225 and 325 series also enhance usability and control. They feature Extron’s integrated control systems, which simplify the operation of entire AV systems. Users benefit from the intuitive user interface, enabling easy switching and management of devices. Additionally, compatibility with third-party control systems allows for seamless integration into existing setups, streamlining operations.

Another noteworthy characteristic is the series’ built-in audio processing capabilities. Both the 225 and 325 models support various audio formats, ensuring high-quality sound output. They also include audio embedding and de-embedding functions, facilitating the integration of audio sources with video signals.

Reliability and durability are hallmarks of the Extron brand, and the 225 and 325 series are no exceptions. Designed for long-term use, these devices undergo rigorous testing to ensure they perform consistently under demanding conditions. Their compact form factor also allows for easy installation in constrained spaces, making them ideal for a variety of environments.

In summary, the Extron Electronics 225 and 325 series deliver top-tier performance, expansive connectivity, and exceptional audio-visual processing capabilities. Their innovative features and robust design make them valuable additions to any AV installation, catering to a wide range of user needs in commercial and educational settings. With Extron’s commitment to quality and user-friendly solutions, the 225 and 325 series stand as testament to their leadership in the AV technology realm.
Top Page Image Contents