Extron electronic 325 manual Configuration Page Video Encoder, Streams panel

Page 43

Configuration Page — Video Encoder

The video encoder configuration page (see figure 26) is accessed by clicking the video icon in the configuration panel of the device page and consists of two panels. This page also provides access to the bandwidth management page via the Bandwidth tab (see “Bandwidth Management Page and Typical Bit Rates“).

1

2

Figure 26. Video Encoder Configuration Page

The top panel of the video encoder configuration page (A on figure 26) provides the following information:

•Name — This field displays the name that is applied to the video port, that is, the name of the image stream. The name is displayed next to the video icon in the configuration panel of the device page. Note that this need not be the same as the name applied to the physical unit itself. You can change the name to a more meaningful value for your installation. Change the device name as follows:

1. Highlight the existing device name.

2. Type the new name.

3.Click the update button.

NOTE: Spaces within names can cause issues when controlling the system

using a third-party control system. Extron recommends avoiding spaces

within names..

•Input Mode — The VN-Matrix 325 codec supports a fully automatic detection of the connected signal format. No manual configuration is required.

•Current Mode — This value reports the currently detected source type.

•Source Status — This value reports the status of the input connection.

•Unplugged — Indicates that either there is no source connected or no invalid video is present.

•Active — Indicates that a valid video connection is present.

Streams panel

The bottom, Streams, panel of the video encoder Configuration page (B on figure 26) provides details of any active video encoder streams. The data transport method, TCP or RTP, is defined on the decoder configuration page (see “Configure Encoders or Decoders”). Multicasting is selected on this page (see “Enable multicast streaming“ to select the multicast and “Data Transport Methods“ for definitions of the methods).

The New Export Stream function is not supported.

VN-Matrix 325 Serial Digital Over IP CODEC • Operation 37

Page 42 Page 44
Image 43
Page 42 Page 44
Contents VN-Matrix325 Safety Instructions English FCC Class a Notice Conventions Used in this Guide Contents VN-Matrix 325 Serial Digital Over IP Codec Contents About the VNC 325 Codec About this GuideVN-Matrix 325 Serial Digital Over IP Codec Introduction Two RS-232 serial ports FeaturesConfigurable as encoder and decoder Two levels of operator interfaceVN-Matrix 325 Serial Digital Over IP Codec Introduction Installation and Setup Overview Installation SetupVNC 325 Features Rear Panel FeaturesPlanning the System Architecture Mounting the UnitsMulticast RTP Data Transport MethodsTypical Unicast RTP Application Unicast RTPUnicast TCP Data and Control RoutingSwitched and Isolated Network Configuration Example 1 Switched and isolated network configurationApplicable Codec Configuration Selections LAN Port Example 2 Switched and isolated network configurationCodec Option LAN Port 1 RJ-45 LAN Port 2 fiber optic Routed Network Configuration Example 3 Routed Network ConfigurationSerial Port Wiring Configuring Network SettingsBaud rate Data bits Parity None Stop bits Flow control None Low-level Network Configuration Controller IP option Configuration MenuConfiguration Selections Configuration SelectionsLAN Port Specific Options Function Comments Ip forwarding Not implemented. Do not change this valueRS-232 Over LAN Port Making Remaining ConnectionsLAN Ports RJ-45 Connector and Pinout Tables RJ-45 port wiringVideo Input, Output, and Loop Connections Encoder configurationLoop BNC connector Not used Decoder configurationStartup and Login Configure Encoders and DecodersDevice List Typical VN-Matrix 325 System Configure the Units as Encoders or DecodersConfiguring a Codec as a Source or Display Enable multicast streaming Encoder Configuration Enable multicast streamingLAN-1 and LAN-2 LEDs Indications and ControlsStatus LED Network Interface Removing a device from the network Device ModeDevice List Device FieldTypical Device Page for an Encoder DeviceDevice summary panel Licensed features panelConfiguration panel Device setup panelMode Streams panel Configuration Page Video EncoderName panel Configuration Page Audio EncoderANC Audio panel Audio Encoder FEC Panel Forward error correction FEC panelAudio Encoder Streams Panel Configuration Page Colfec and Rowfec EncodersFEC Encoder Streams Panel Bandwidth Management Page and Typical Bit RatesBandwidth Management Standard Controls Panel Bandwidth management standard controls panelAdvanced Controls Panel Advanced Controls panelBandwidth Management Broadcast Contribution Video Bit Typical Embedded Audio Bit Rates in Transparent ModePeak flow rate Maximum bit ratesDecoder Video Configuration Panel Decoder Display and ConfigurationDecoder Streams Configuration Panel Decoder Streams Configuration PanelDecoder Bit Rate and Stream Decoder Bit Rate and StreamRaw Network Statistics Panel Pass-through Control Peripherals Page and Serial Port ControlConfiguring a Serial Pass-through Group Configuring a Serial Pass-through GroupFirmware Upgrade Stages Function Summary Perform on Firmware UpgradeUpgrade Uploading the upgrade to the controller codecInstalling the firmware prepare, activate, and commit stages License Passwords Panel Accounts Page Passwords and Clock ManagementController Licensing Panel Clock Management PanelAlarms AlarmsNone Filter settings panelAlarm Source Alarm Severity Description CriticalEncoder Alarm Type and Description Action Default Settings Alarm list panelAlarm types and descriptions Encoder AlarmIndicates that there is a valid Alarm Log Alarm LogsSimple Network Management Protocol Snmp Password ValueSnmp Trap Destination Values Snmp Community ValueVideo processing codec SpecificationsVideo Video input and loop through encoderControl host ports codecs, decoders Sync genlock decoderAudio input and output Audio processingGeneral Network transportOptional SFP Module Part Numbers and AccessoriesMounting and Power Options Codec Part Number and Included PartsUL Rack-Mounting Guidelines Mounting the CodecTabletop Use Mounting kitsOutput format Test Pattern1280 x 720x480 Extron Warranty
Related manuals
Manual 4 pages 38.42 Kb

325 specifications

Extron Electronics has established itself as a key player in the AV technology industry, providing innovative solutions for a wide range of applications. Among their product lineup, the Extron Electronics 225 and 325 series of devices stand out for their advanced features, technologies, and characteristics that cater to both commercial and educational environments.

The Extron 225 and 325 series are designed for seamless integration into various AV systems, offering unparalleled performance and reliability. At the core of these devices is their robust signal processing capability. Both models are equipped with high-performance scalers and switchers that ensure optimal video quality. They support a wide range of resolutions, including 4K, enabling users to connect various sources without compromising image fidelity.

One of the key features of the 225 and 325 series is their versatile connectivity options. These devices come with multiple inputs, including HDMI, VGA, and composite, allowing for the integration of various AV sources. The series also includes configurable outputs, which can be customized according to the specific requirements of the installation. This flexibility is vital in multipurpose spaces where different AV setups are needed.

The technologies embedded in the 225 and 325 series also enhance usability and control. They feature Extron’s integrated control systems, which simplify the operation of entire AV systems. Users benefit from the intuitive user interface, enabling easy switching and management of devices. Additionally, compatibility with third-party control systems allows for seamless integration into existing setups, streamlining operations.

Another noteworthy characteristic is the series’ built-in audio processing capabilities. Both the 225 and 325 models support various audio formats, ensuring high-quality sound output. They also include audio embedding and de-embedding functions, facilitating the integration of audio sources with video signals.

Reliability and durability are hallmarks of the Extron brand, and the 225 and 325 series are no exceptions. Designed for long-term use, these devices undergo rigorous testing to ensure they perform consistently under demanding conditions. Their compact form factor also allows for easy installation in constrained spaces, making them ideal for a variety of environments.

In summary, the Extron Electronics 225 and 325 series deliver top-tier performance, expansive connectivity, and exceptional audio-visual processing capabilities. Their innovative features and robust design make them valuable additions to any AV installation, catering to a wide range of user needs in commercial and educational settings. With Extron’s commitment to quality and user-friendly solutions, the 225 and 325 series stand as testament to their leadership in the AV technology realm.
Top Page Image Contents