Extron electronic Configure the Units as Encoders or Decoders, Typical VN-Matrix 325 System

Page 33

Configure the Units as Encoders or Decoders

A typical VN-Matrix 325 network (see figure 17) includes an encoder (source), a decoder (display), and a controlling PC. The data transport method, TCP or RTP, is defined on the decoder configuration page. Multicasting is selected on the encoder configuration page (see “Enable multicast streaming“ to select the multicast and “Data Transport Methods“ for definitions of the methods).

 

Encoded Video and Control

Encoded Video

 

 

 

 

Network

 

 

 

Encoder Configuration

 

 

Decoder Configuration

 

 

REMOTE

RS-232

 

REMOTE

RS-232

POWER

OPTICAL

OVER LAN

POWER

OPTICAL

OVER LAN

 

 

12V DC

1 LAN 2

 

12V DC

1 LAN 2

 

3A MAX

 

3A MAX

 

Decoded

Video

Optional

Local

Monitor

Digital Video Source

Control and

 

Monitor

 

Monitoring

 

 

Figure 17. Typical VN-Matrix 325 System

The Mode column on the Device List page (see figure 18) shows how each VNC 325 unit is configured using the following icons:

= Encoder = Decoder = VNM Recorder = Undefined

NOTE: If this is the initial setup, none of the devices have been defined and thus show the icon in the Mode column.

1

Figure 18. Selecting a Device

NOTES: The VNM Recorder is not documented in this guide. Inclusion in this list is for

completeness and reference only.

Only devices that are or have been configured to connect to the system controller (using the procedure detailed in “Configuring Network Settings“) are listed.

The device list may show more devices than are in your system. This is because the controller maintains a list of devices that have been used in the past and are not currently available. In this case, the IP address entry for that device is blank.

If desired, remove devices that have been physically removed from the system from this listing by clicking the Delete icon ().

VN-Matrix 325 Serial Digital Over IP CODEC • Installation and Setup 27

Image 33
Contents VN-Matrix325 Safety Instructions English FCC Class a Notice Conventions Used in this Guide Contents VN-Matrix 325 Serial Digital Over IP Codec Contents About the VNC 325 Codec About this GuideVN-Matrix 325 Serial Digital Over IP Codec Introduction Configurable as encoder and decoder FeaturesTwo levels of operator interface Two RS-232 serial portsVN-Matrix 325 Serial Digital Over IP Codec Introduction Installation and Setup Overview Installation SetupVNC 325 Features Rear Panel FeaturesPlanning the System Architecture Mounting the UnitsMulticast RTP Data Transport MethodsTypical Unicast RTP Application Unicast RTPUnicast TCP Data and Control RoutingSwitched and Isolated Network Configuration Example 1 Switched and isolated network configurationApplicable Codec Configuration Selections LAN Port Example 2 Switched and isolated network configurationCodec Option LAN Port 1 RJ-45 LAN Port 2 fiber optic Routed Network Configuration Example 3 Routed Network ConfigurationConfiguring Network Settings Serial Port WiringBaud rate Data bits Parity None Stop bits Flow control None Low-level Network Configuration Controller IP option Configuration MenuConfiguration Selections Configuration SelectionsLAN Port Specific Options Function Comments Ip forwarding Not implemented. Do not change this valueMaking Remaining Connections RS-232 Over LAN PortLAN Ports RJ-45 Connector and Pinout Tables RJ-45 port wiringVideo Input, Output, and Loop Connections Encoder configurationLoop BNC connector Not used Decoder configurationStartup and Login Configure Encoders and DecodersDevice List Typical VN-Matrix 325 System Configure the Units as Encoders or DecodersConfiguring a Codec as a Source or Display Enable multicast streaming Encoder Configuration Enable multicast streamingIndications and Controls LAN-1 and LAN-2 LEDsStatus LED Network Interface Device List Device ModeDevice Field Removing a device from the networkTypical Device Page for an Encoder DeviceDevice summary panel Licensed features panelDevice setup panel Configuration panelMode Streams panel Configuration Page Video EncoderName panel Configuration Page Audio EncoderANC Audio panel Audio Encoder FEC Panel Forward error correction FEC panelAudio Encoder Streams Panel Configuration Page Colfec and Rowfec EncodersFEC Encoder Streams Panel Bandwidth Management Page and Typical Bit RatesBandwidth Management Standard Controls Panel Bandwidth management standard controls panelAdvanced Controls Panel Advanced Controls panelBandwidth Management Peak flow rate Typical Embedded Audio Bit Rates in Transparent ModeMaximum bit rates Broadcast Contribution Video BitDecoder Video Configuration Panel Decoder Display and ConfigurationDecoder Streams Configuration Panel Decoder Streams Configuration PanelDecoder Bit Rate and Stream Decoder Bit Rate and StreamRaw Network Statistics Panel Pass-through Control Peripherals Page and Serial Port ControlConfiguring a Serial Pass-through Group Configuring a Serial Pass-through GroupFirmware Upgrade Stages Function Summary Perform on Firmware UpgradeUpgrade Uploading the upgrade to the controller codecInstalling the firmware prepare, activate, and commit stages License Passwords Panel Accounts Page Passwords and Clock ManagementController Licensing Panel Clock Management PanelAlarms AlarmsAlarm Source Filter settings panelAlarm Severity Description Critical NoneAlarm types and descriptions Alarm list panelEncoder Alarm Encoder Alarm Type and Description Action Default SettingsIndicates that there is a valid Alarm Log Alarm LogsSimple Network Management Protocol Snmp Password ValueSnmp Trap Destination Values Snmp Community ValueVideo SpecificationsVideo input and loop through encoder Video processing codecAudio input and output Sync genlock decoderAudio processing Control host ports codecs, decodersGeneral Network transportMounting and Power Options Part Numbers and AccessoriesCodec Part Number and Included Parts Optional SFP ModuleTabletop Use Mounting the CodecMounting kits UL Rack-Mounting GuidelinesTest Pattern Output format1280 x 720x480 Extron Warranty
Related manuals
Manual 4 pages 38.42 Kb

325 specifications

Extron Electronics has established itself as a key player in the AV technology industry, providing innovative solutions for a wide range of applications. Among their product lineup, the Extron Electronics 225 and 325 series of devices stand out for their advanced features, technologies, and characteristics that cater to both commercial and educational environments.

The Extron 225 and 325 series are designed for seamless integration into various AV systems, offering unparalleled performance and reliability. At the core of these devices is their robust signal processing capability. Both models are equipped with high-performance scalers and switchers that ensure optimal video quality. They support a wide range of resolutions, including 4K, enabling users to connect various sources without compromising image fidelity.

One of the key features of the 225 and 325 series is their versatile connectivity options. These devices come with multiple inputs, including HDMI, VGA, and composite, allowing for the integration of various AV sources. The series also includes configurable outputs, which can be customized according to the specific requirements of the installation. This flexibility is vital in multipurpose spaces where different AV setups are needed.

The technologies embedded in the 225 and 325 series also enhance usability and control. They feature Extron’s integrated control systems, which simplify the operation of entire AV systems. Users benefit from the intuitive user interface, enabling easy switching and management of devices. Additionally, compatibility with third-party control systems allows for seamless integration into existing setups, streamlining operations.

Another noteworthy characteristic is the series’ built-in audio processing capabilities. Both the 225 and 325 models support various audio formats, ensuring high-quality sound output. They also include audio embedding and de-embedding functions, facilitating the integration of audio sources with video signals.

Reliability and durability are hallmarks of the Extron brand, and the 225 and 325 series are no exceptions. Designed for long-term use, these devices undergo rigorous testing to ensure they perform consistently under demanding conditions. Their compact form factor also allows for easy installation in constrained spaces, making them ideal for a variety of environments.

In summary, the Extron Electronics 225 and 325 series deliver top-tier performance, expansive connectivity, and exceptional audio-visual processing capabilities. Their innovative features and robust design make them valuable additions to any AV installation, catering to a wide range of user needs in commercial and educational settings. With Extron’s commitment to quality and user-friendly solutions, the 225 and 325 series stand as testament to their leadership in the AV technology realm.