Extron electronic 325 manual Device summary panel, Licensed features panel

Page 41

Device summary panel

This panel consists of the following fields:

•Name — This field displays the name of the device. You can change the name of the unit to a more meaningful value for your installation as follows:

1. Highlight the existing device name.

2. Type the new name.

3.Click the update button.

NOTE: Spaces within names can cause issues when controlling the system

using a third-party control system. Extron recommends avoiding spaces

within names..

•Serial Number — This read-only field displays the serial number of the device, information is required when upgrading the licence on a device.

•Device Status — This read-only field displays either of the following messages:

•Active — The device is present and operating.

•Inactive — The controller cannot contact the device. It may be powered down or the network cable is unplugged.

•IP address: port — This read-only field displays two pieces of information:

•The IP address that is assigned to LAN port 1.

•The port numbers that have been configured for send and receive of UDP control information. By default these are 9001 (send) and 5432 (receive).

•Link Status — This read-only field displays the condition of the Ethernet network link to the controller in one of the following messages:

•Good — There is little or no control data packet loss.

•Fair — There is a small amount of control data packet loss.

•Poor — A bad network link exists.

Licensed features panel

This panel consists of the following read-only fields, which provides a description of features that are enabled on the device:

•Video — For the VNC 325, this field always reads 3G-SDI.

•Audio — For the VNC 325, this field always reads 16.

The licence management button opens the License page where additional features may be enabled.

VN-Matrix 325 Serial Digital Over IP CODEC • Operation 35

Page 40 Page 42
Image 41
Page 40 Page 42
Contents VN-Matrix325 Safety Instructions English FCC Class a Notice Conventions Used in this Guide Contents VN-Matrix 325 Serial Digital Over IP Codec Contents About the VNC 325 Codec About this GuideVN-Matrix 325 Serial Digital Over IP Codec Introduction Configurable as encoder and decoder FeaturesTwo levels of operator interface Two RS-232 serial portsVN-Matrix 325 Serial Digital Over IP Codec Introduction Installation and Setup Overview Installation SetupVNC 325 Features Rear Panel FeaturesPlanning the System Architecture Mounting the UnitsMulticast RTP Data Transport MethodsTypical Unicast RTP Application Unicast RTPUnicast TCP Data and Control RoutingSwitched and Isolated Network Configuration Example 1 Switched and isolated network configurationApplicable Codec Configuration Selections LAN Port Example 2 Switched and isolated network configurationCodec Option LAN Port 1 RJ-45 LAN Port 2 fiber optic Routed Network Configuration Example 3 Routed Network ConfigurationBaud rate Data bits Parity None Stop bits Flow control None Configuring Network SettingsSerial Port Wiring Low-level Network Configuration Controller IP option Configuration MenuConfiguration Selections Configuration SelectionsLAN Port Specific Options Function Comments Ip forwarding Not implemented. Do not change this valueLAN Ports Making Remaining ConnectionsRS-232 Over LAN Port RJ-45 Connector and Pinout Tables RJ-45 port wiringVideo Input, Output, and Loop Connections Encoder configurationLoop BNC connector Not used Decoder configurationStartup and Login Configure Encoders and DecodersDevice List Typical VN-Matrix 325 System Configure the Units as Encoders or DecodersConfiguring a Codec as a Source or Display Enable multicast streaming Encoder Configuration Enable multicast streamingStatus LED Indications and ControlsLAN-1 and LAN-2 LEDs Network Interface Device List Device ModeDevice Field Removing a device from the networkTypical Device Page for an Encoder DeviceDevice summary panel Licensed features panelMode Device setup panelConfiguration panel Streams panel Configuration Page Video EncoderName panel Configuration Page Audio EncoderANC Audio panel Audio Encoder FEC Panel Forward error correction FEC panelAudio Encoder Streams Panel Configuration Page Colfec and Rowfec EncodersFEC Encoder Streams Panel Bandwidth Management Page and Typical Bit RatesBandwidth Management Standard Controls Panel Bandwidth management standard controls panelAdvanced Controls Panel Advanced Controls panelBandwidth Management Peak flow rate Typical Embedded Audio Bit Rates in Transparent ModeMaximum bit rates Broadcast Contribution Video BitDecoder Video Configuration Panel Decoder Display and ConfigurationDecoder Streams Configuration Panel Decoder Streams Configuration PanelDecoder Bit Rate and Stream Decoder Bit Rate and StreamRaw Network Statistics Panel Pass-through Control Peripherals Page and Serial Port ControlConfiguring a Serial Pass-through Group Configuring a Serial Pass-through GroupFirmware Upgrade Stages Function Summary Perform on Firmware UpgradeUpgrade Uploading the upgrade to the controller codecInstalling the firmware prepare, activate, and commit stages License Passwords Panel Accounts Page Passwords and Clock ManagementController Licensing Panel Clock Management PanelAlarms AlarmsAlarm Source Filter settings panelAlarm Severity Description Critical NoneAlarm types and descriptions Alarm list panelEncoder Alarm Encoder Alarm Type and Description Action Default SettingsIndicates that there is a valid Alarm Log Alarm LogsSimple Network Management Protocol Snmp Password ValueSnmp Trap Destination Values Snmp Community ValueVideo SpecificationsVideo input and loop through encoder Video processing codecAudio input and output Sync genlock decoderAudio processing Control host ports codecs, decodersGeneral Network transportMounting and Power Options Part Numbers and AccessoriesCodec Part Number and Included Parts Optional SFP ModuleTabletop Use Mounting the CodecMounting kits UL Rack-Mounting Guidelines1280 x 720x480 Test PatternOutput format Extron Warranty
Related manuals
Manual 4 pages 38.42 Kb

325 specifications

Extron Electronics has established itself as a key player in the AV technology industry, providing innovative solutions for a wide range of applications. Among their product lineup, the Extron Electronics 225 and 325 series of devices stand out for their advanced features, technologies, and characteristics that cater to both commercial and educational environments.

The Extron 225 and 325 series are designed for seamless integration into various AV systems, offering unparalleled performance and reliability. At the core of these devices is their robust signal processing capability. Both models are equipped with high-performance scalers and switchers that ensure optimal video quality. They support a wide range of resolutions, including 4K, enabling users to connect various sources without compromising image fidelity.

One of the key features of the 225 and 325 series is their versatile connectivity options. These devices come with multiple inputs, including HDMI, VGA, and composite, allowing for the integration of various AV sources. The series also includes configurable outputs, which can be customized according to the specific requirements of the installation. This flexibility is vital in multipurpose spaces where different AV setups are needed.

The technologies embedded in the 225 and 325 series also enhance usability and control. They feature Extron’s integrated control systems, which simplify the operation of entire AV systems. Users benefit from the intuitive user interface, enabling easy switching and management of devices. Additionally, compatibility with third-party control systems allows for seamless integration into existing setups, streamlining operations.

Another noteworthy characteristic is the series’ built-in audio processing capabilities. Both the 225 and 325 models support various audio formats, ensuring high-quality sound output. They also include audio embedding and de-embedding functions, facilitating the integration of audio sources with video signals.

Reliability and durability are hallmarks of the Extron brand, and the 225 and 325 series are no exceptions. Designed for long-term use, these devices undergo rigorous testing to ensure they perform consistently under demanding conditions. Their compact form factor also allows for easy installation in constrained spaces, making them ideal for a variety of environments.

In summary, the Extron Electronics 225 and 325 series deliver top-tier performance, expansive connectivity, and exceptional audio-visual processing capabilities. Their innovative features and robust design make them valuable additions to any AV installation, catering to a wide range of user needs in commercial and educational settings. With Extron’s commitment to quality and user-friendly solutions, the 225 and 325 series stand as testament to their leadership in the AV technology realm.
Top Page Image Contents