Gigabyte GA-K8NMF-9 user manual Cpufan / Sysfan Cooler Fan Power Connector, FDD FDD Connector

Page 20

English

3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin power connector and possesses a foolproof connection design.

Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND).

Please remember to connect the power to the cooler to prevent system overheating and failure. Caution!

Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.

						Pin No.	Definition
	1					1	GND
						1	GND
						2	+12V


	CPU_FAN / SYS_FAN
	CPU_FAN / SYS_FAN					3	Sense
						3	Sense

5)FDD (FDD Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Please connect the red power connector wire to the pin1 position.

3433

21

GA-K8NMF-9 Motherboard

- 20 -

Image 20

Contents GA-K8NMF-9 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NMF-9 Motherboard Layout K8NMF-9Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary SATA2, SATA3Bios Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector BAT Battery Fpanel Front Panel JumperFaudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector 15 F11394 Front Ieee 1394 ConnectorsCI Chassis Intrusion, Case Open Clrcmos Clear CmosEnglish English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F8 F12 For Boot Menu„ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationTime IDE Channel 0 Master/Slave IDE Channel 1 Master/SlaveFloppy 3 Mode Support for Japan Area IDE Channel 2/3/4/5 MasterDrive a / Drive B Halt onHard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek Password CheckIntegrated Peripherals Init Display FirstIDE DMA transfer access On-Chip LAN Boot ROMOn-Chip IDE Channel0 On-Chip IDE Channel1IDE Prefetch Mode NV Sata 1 Primary RAIDNV Sata 1 Secondary RAID NV Sata 2 class codeNoteParallel Port Mode ECP Mode Use DMAOnboard Parallel Port On-Chip USBPower-On by Alarm PME Event Wake UpModem Ring On USB Resume from SuspendPower On by Mouse Power On by KeyboardKB Power on Password AC Back FunctionCurrent VoltageV Vcore / DDR25V / +3.3V / +12V PC Health StatusCase Opened Current CPU Temperature CPU Warning TemperatureTemp of FAN turn off Default temperature 0oC Current CPU/SYSTEM FAN Speed RPMTemp Limit of Low Speed Default temperature 20oC Temp Limit of Mid Speed Default temperature 50oCTemp Limit of High Speed Default temperature 60oC Temp of full FAN Speed Default temperature 70oCLoad Optimized Defaults Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Remove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupUsing the Define a New Array Window Selecting the RAID ModeSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting Contact Us Taiwan HeadquartersChina Shanghai