Gigabyte GA-K8NMF-9 user manual Installation of the Fan Heat Sink

Page 13

1-3-2 Installation of the Fan Heat Sink

Fig.1

Before installing the heat sink, please first add an even layer of heat sink paste on the surface of the CPU. Install all the heat sink components (Please refer to the heat sink manual for detailed installation instructions).

Fig.2

Please connect the heat sink power connector to the CPU_FAN connector located on the motherboard so that the heat sink can properly function to prevent CPU overheating.

The heat sink may adhere to the CPU as a result of hardening of the heat sink paste. To prevent such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used for heat dissipation or using extreme care when removing the heat sink.

English

- 13 -

Hardware Installation

Image 13

Contents GA-K8NMF-9 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation K8NMF-9 GA-K8NMF-9 Motherboard LayoutBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerSATA2, SATA3 Feature SummaryBios Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorIDE1 / IDE2 IDE Connector Fpanel Front Panel Jumper BAT BatteryCdin CD In Connector Faudio Front Audio Panel ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center Connector15 F11394 Front Ieee 1394 Connectors USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos CI Chassis Intrusion, Case OpenEnglish English Main Menu Status Page Setup Menu / Option Page Setup MenuF12 For Boot Menu Main Menu For example Bios Ver. F8„ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave TimeIDE Channel 2/3/4/5 Master Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onFirst / Second / Third Boot Device Hard Disk Boot PriorityBoot Up Floppy Seek Password CheckInit Display First Integrated PeripheralsOn-Chip LAN Boot ROM IDE DMA transfer accessOn-Chip IDE Channel0 On-Chip IDE Channel1NV Sata 1 Primary RAID IDE Prefetch ModeNV Sata 1 Secondary RAID NV Sata 2 class codeNoteECP Mode Use DMA Parallel Port ModeOnboard Parallel Port On-Chip USBPME Event Wake Up Power-On by AlarmModem Ring On USB Resume from SuspendPower On by Keyboard Power On by MouseKB Power on Password AC Back FunctionCase Opened PC Health StatusCurrent VoltageV Vcore / DDR25V / +3.3V / +12V CPU Warning Temperature Current CPU TemperatureTemp of FAN turn off Default temperature 0oC Current CPU/SYSTEM FAN Speed RPMTemp Limit of Mid Speed Default temperature 50oC Temp Limit of Low Speed Default temperature 20oCTemp Limit of High Speed Default temperature 60oC Temp of full FAN Speed Default temperature 70oCLoad Optimized Defaults Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosSelecting the RAID Mode Using the Define a New Array WindowSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction Introduction of audio connectorsAuto-detecting Enable UAJ function Manual settingUAJ Introduction Troubleshooting Taiwan Headquarters Contact UsChina Shanghai