Gigabyte GA-K8NMF-9 user manual Channel Audio Setup

Page 71

4 Channel Audio Setup

STEP 1:

Connect the Front Speakers to "Line Out", the Rear

Speakers to "Line In".

Line In (Rear Speaker Out)

Line Out (Front Speaker Out)

STEP 2:

Following installation of the audio driver, you'll find a

Sound Effect icon on the lower right hand taskbar.

Click the icon to select the function.

STEP 3:

Click "Speaker Configuration" and select the "UAJ Function". Then click on the left selection bar and select "4CH Speaker" to complete 4 channel audio configuration.

English

- 71 -

Appendix

Image 71
Contents GA-K8NMF-9 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation K8NMF-9 GA-K8NMF-9 Motherboard LayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantySATA2, SATA3 Feature SummaryBios Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorIDE1 / IDE2 IDE Connector Fpanel Front Panel Jumper BAT BatteryCdin CD In Connector Faudio Front Audio Panel ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center Connector15 F11394 Front Ieee 1394 Connectors USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos CI Chassis Intrusion, Case OpenEnglish English Main Menu Status Page Setup Menu / Option Page Setup MenuF12 For Boot Menu Main Menu For example Bios Ver. F8„ PnP/PCI Configuration „ Standard Cmos Features„ Advanced Bios Features „ Power Management SetupIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave TimeHalt on Floppy 3 Mode Support for Japan AreaIDE Channel 2/3/4/5 Master Drive a / Drive BPassword Check Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Floppy SeekInit Display First Integrated PeripheralsOn-Chip IDE Channel1 IDE DMA transfer accessOn-Chip LAN Boot ROM On-Chip IDE Channel0NV Sata 2 class codeNote IDE Prefetch ModeNV Sata 1 Primary RAID NV Sata 1 Secondary RAIDOn-Chip USB Parallel Port ModeECP Mode Use DMA Onboard Parallel PortUSB Resume from Suspend Power-On by AlarmPME Event Wake Up Modem Ring OnAC Back Function Power On by MousePower On by Keyboard KB Power on PasswordCurrent VoltageV Vcore / DDR25V / +3.3V / +12V PC Health StatusCase Opened Current CPU/SYSTEM FAN Speed RPM Current CPU TemperatureCPU Warning Temperature Temp of FAN turn off Default temperature 0oCTemp of full FAN Speed Default temperature 70oC Temp Limit of Low Speed Default temperature 20oCTemp Limit of Mid Speed Default temperature 50oC Temp Limit of High Speed Default temperature 60oCLoad Optimized Defaults Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosAssigning the Disks Using the Define a New Array WindowSelecting the RAID Mode Selecting the Striping Block SizeCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting Taiwan Headquarters Contact UsChina Shanghai