Gigabyte GA-K8NMF-9 user manual F9 For Xpress Recovery

Page 53

2.Press F9 during powering on the computer. (Text Mode) Press F9 during powering on the computer .

Award Modular BIOS v6.00PG, An Energy Star Al ly Copyright (C) 1984-2004, Award Software, Inc.

Intel 865PE AGPSet BIOS for 8IPE1000MT F1 Check System Health OK

.

.

.

Press DEL to enter SETUP / Q-Flash, F9 For Xpress Recovery 08/16/2002-I845GE-6A69YG01C-00

F9 For Xpress Recovery

English

Xpress Recovery V1.0 (C) Copy Right 2003. GIGABYTE Technology CO. , Ltd.
1.	Execute Backup Utility
2.	Execute Restore Utility
3. Remove Backup Image
4.	Set Password
5.	Exit and Restart

1.If you have already entered Xpress Recovery by booting from the CD-ROM, you can enter Xpress Recovery in the future by pressing the F9 key.

2.System storage capacity as well as drive reading/writing speed will affect backup speed.

3.It is recommended that Xpress Recovery be immediately installed after OS and all required driver and software installations are complete.

- 53 -

Appendix

Image 53

Contents GA-K8NMF-9 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation K8NMF-9 GA-K8NMF-9 Motherboard LayoutBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerSATA2, SATA3 Feature SummaryBios Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorIDE1 / IDE2 IDE Connector Fpanel Front Panel Jumper BAT BatteryCdin CD In Connector Faudio Front Audio Panel ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center Connector15 F11394 Front Ieee 1394 Connectors USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos CI Chassis Intrusion, Case OpenEnglish English Main Menu Status Page Setup Menu / Option Page Setup MenuF12 For Boot Menu Main Menu For example Bios Ver. F8„ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave TimeIDE Channel 2/3/4/5 Master Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onFirst / Second / Third Boot Device Hard Disk Boot PriorityBoot Up Floppy Seek Password CheckInit Display First Integrated PeripheralsOn-Chip LAN Boot ROM IDE DMA transfer accessOn-Chip IDE Channel0 On-Chip IDE Channel1NV Sata 1 Primary RAID IDE Prefetch ModeNV Sata 1 Secondary RAID NV Sata 2 class codeNoteECP Mode Use DMA Parallel Port ModeOnboard Parallel Port On-Chip USBPME Event Wake Up Power-On by AlarmModem Ring On USB Resume from SuspendPower On by Keyboard Power On by MouseKB Power on Password AC Back FunctionCurrent VoltageV Vcore / DDR25V / +3.3V / +12V PC Health StatusCase Opened CPU Warning Temperature Current CPU TemperatureTemp of FAN turn off Default temperature 0oC Current CPU/SYSTEM FAN Speed RPMTemp Limit of Mid Speed Default temperature 50oC Temp Limit of Low Speed Default temperature 20oCTemp Limit of High Speed Default temperature 60oC Temp of full FAN Speed Default temperature 70oCLoad Optimized Defaults Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosSelecting the RAID Mode Using the Define a New Array WindowSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting Taiwan Headquarters Contact UsChina Shanghai