Gigabyte GA-K8NMF-9 user manual Completing the RAID Bios Setup

Page 67

Completing the RAID BIOS Setup

After assigning your RAID array disks, press F7. The Clear disk data prompt appears.

NVIDIA RAID Utility Jan 12 2005

- Define a New Array -

RAID Mode: Mirroring

 

 

Striping Block: Optimal

Free Disks

Clear disk dataArray? Disks

Loc

Disk Model Name

 

 

Loc

Disk Model Name

 

 

[Y] YES

2.1.M

ST3120026AS

 

 

[N] NO

ST3120026AS

 

 

[

] Add

2.0.M

 

 

[

] Del

 

 

 

[ESC] Quit [F6] Back

[F7] Finish

[TAB] Navigate

[ ] Select [ENTER] Popup

Press Y if you want to wipe out all the data from the RAID array, otherwise press N. You must choose Yes if the drives were previously used as RAID drives. The Array List window appears, where you can review the RAID arrays that you have set up.

You can select a disk array as boot device if you want to boot operating system from an array. Use the arrow keys to select the array, then press B to specify the array as bootable.

 

 

NVIDIA RAID Utility

Jan 12 2005

 

 

 

- Array List -

Boot

Id

Status

Vendor

Array Model Name

Yes

2

Healthy

NVIDIA

MIRROR 111.79G

[Ctrl-X] Exit

[

] Select

[B] Set Boot

[N] New Array [ENTER] Detail

English

- 67 -

Appendix

Image 67
Contents GA-K8NMF-9 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation K8NMF-9 GA-K8NMF-9 Motherboard LayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantySATA2, SATA3 Feature SummaryBios Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorIDE1 / IDE2 IDE Connector Fpanel Front Panel Jumper BAT BatteryCdin CD In Connector Faudio Front Audio Panel ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center Connector15 F11394 Front Ieee 1394 Connectors USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos CI Chassis Intrusion, Case OpenEnglish English Main Menu Status Page Setup Menu / Option Page Setup MenuF12 For Boot Menu Main Menu For example Bios Ver. F8„ PnP/PCI Configuration „ Standard Cmos Features„ Advanced Bios Features „ Power Management SetupIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave TimeHalt on Floppy 3 Mode Support for Japan AreaIDE Channel 2/3/4/5 Master Drive a / Drive BPassword Check Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Floppy SeekInit Display First Integrated PeripheralsOn-Chip IDE Channel1 IDE DMA transfer accessOn-Chip LAN Boot ROM On-Chip IDE Channel0NV Sata 2 class codeNote IDE Prefetch ModeNV Sata 1 Primary RAID NV Sata 1 Secondary RAIDOn-Chip USB Parallel Port ModeECP Mode Use DMA Onboard Parallel PortUSB Resume from Suspend Power-On by AlarmPME Event Wake Up Modem Ring OnAC Back Function Power On by MousePower On by Keyboard KB Power on PasswordCase Opened PC Health StatusCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPM Current CPU TemperatureCPU Warning Temperature Temp of FAN turn off Default temperature 0oCTemp of full FAN Speed Default temperature 70oC Temp Limit of Low Speed Default temperature 20oCTemp Limit of Mid Speed Default temperature 50oC Temp Limit of High Speed Default temperature 60oCLoad Optimized Defaults Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosAssigning the Disks Using the Define a New Array WindowSelecting the RAID Mode Selecting the Striping Block SizeCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction Introduction of audio connectorsAuto-detecting Enable UAJ function Manual settingUAJ Introduction Troubleshooting Taiwan Headquarters Contact UsChina Shanghai