Gigabyte GA-K8NMF-9 user manual Table of Contents

Page 4

Table of Contents

GA-K8NMF-9 Motherboard Layout

6

Block Diagram

7

Chapter 1 Hardware Installation

9

1-1

Considerations Prior to Installation

9

1-2

Feature Summary

10

1-3

Installation of the CPU and Fan Heat Sink

12

1-3-1 Installation of the CPU

12

1-3-2 Installation of the Fan Heat Sink

13

1-4

Installation of Memory

14

1-5

Installation of Expansion Cards

16

1-6

I/O Back Panel Introduction

17

1-7

Connectors Introduction

18

Chapter 2 BIOS Setup

29

The Main Menu (For example: BIOS Ver. : F1)

30

2-1

Standard CMOS Features

31

2-2

Advanced BIOS Features

33

2-3

Integrated Peripherals

35

2-4

Power Management Setup

39

2-5

PnP/PCI Configurations

40

2-6

PC Health Status

41

2-7

Load Optimized Defaults

43

2-8

Set Supervisor/User Password

43

2-9

Save & Exit Setup

44

2-10

Exit Without Saving

44

- 4 -

Image 4
Contents GA-K8NMF-9 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NMF-9 Motherboard Layout K8NMF-9Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary SATA2, SATA3Bios Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector BAT Battery Fpanel Front Panel JumperFaudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector 15 F11394 Front Ieee 1394 ConnectorsCI Chassis Intrusion, Case Open Clrcmos Clear CmosEnglish English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F8 F12 For Boot Menu„ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationTime IDE Channel 0 Master/Slave IDE Channel 1 Master/SlaveFloppy 3 Mode Support for Japan Area IDE Channel 2/3/4/5 MasterDrive a / Drive B Halt onHard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek Password CheckIntegrated Peripherals Init Display FirstIDE DMA transfer access On-Chip LAN Boot ROMOn-Chip IDE Channel0 On-Chip IDE Channel1IDE Prefetch Mode NV Sata 1 Primary RAIDNV Sata 1 Secondary RAID NV Sata 2 class codeNoteParallel Port Mode ECP Mode Use DMAOnboard Parallel Port On-Chip USBPower-On by Alarm PME Event Wake UpModem Ring On USB Resume from SuspendPower On by Mouse Power On by KeyboardKB Power on Password AC Back FunctionCase Opened PC Health StatusCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU Temperature CPU Warning TemperatureTemp of FAN turn off Default temperature 0oC Current CPU/SYSTEM FAN Speed RPMTemp Limit of Low Speed Default temperature 20oC Temp Limit of Mid Speed Default temperature 50oCTemp Limit of High Speed Default temperature 60oC Temp of full FAN Speed Default temperature 70oCLoad Optimized Defaults Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupUsing the Define a New Array Window Selecting the RAID ModeSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction Introduction of audio connectorsAuto-detecting Enable UAJ function Manual settingUAJ Introduction Troubleshooting Contact Us Taiwan HeadquartersChina Shanghai