Gigabyte GA-K8NMF-9 Onboard Parallel Port, Parallel Port Mode, ECP Mode Use DMA, On-Chip USB

Page 38

English

Onboard Parallel Port

Disabled

Disable onboard LPT port.

378/IRQ7

Enable onboard LPT port and address is 378/IRQ7. (Default value)

278/IRQ5

Enable onboard LPT port and address is 278/IRQ5.

3BC/IRQ7

Enable onboard LPT port and address is 3BC/IRQ7.

Parallel Port Mode

SPP

Using Parallel port as Standard Parallel Port. (Default value)

EPP

Using Parallel port as Enhanced Parallel Port.

ECP

Using Parallel port as Extended Capabilities Port.

ECP+EPP

Using Parallel port as ECP and EPP mode.

ECP Mode Use DMA

3

Set ECP Mode Use DMA to 3. (Default value)

1

Set ECP Mode Use DMA to 1.

On-Chip USB

Disabled

Disable this function if you are not using onboard USB function.

V1.1+V2.0

Enable USB 1.1 and USB 2.0 controller. (Default value)

V1.1

Enable only USB 1.1 controller.

Legacy USB Keyboard/Storage

Enabled

Enable USB keyboard support in the MS-DOS environment.

Disabled

Disable this function. (Default value)

Legacy (DOS) USB Mouse

Enabled

Enable USB mouse support in the MS-DOS environment.

Disabled

Disable this function. (Default value)

Legacy USB Storage detect

Enabled

Enable USB storage detection function. (Default value)

Disabled

Disable this function.

GA-K8NMF-9 Motherboard

- 38 -

Image 38
Contents GA-K8NMF-9 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NMF-9 Motherboard Layout K8NMF-9Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary SATA2, SATA3Bios Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector BAT Battery Fpanel Front Panel JumperFaudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector 15 F11394 Front Ieee 1394 ConnectorsCI Chassis Intrusion, Case Open Clrcmos Clear CmosEnglish English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F8 F12 For Boot Menu„ Power Management Setup „ Standard Cmos Features„ Advanced Bios Features „ PnP/PCI ConfigurationTime IDE Channel 0 Master/Slave IDE Channel 1 Master/SlaveDrive a / Drive B Floppy 3 Mode Support for Japan AreaIDE Channel 2/3/4/5 Master Halt onBoot Up Floppy Seek Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckIntegrated Peripherals Init Display FirstOn-Chip IDE Channel0 IDE DMA transfer accessOn-Chip LAN Boot ROM On-Chip IDE Channel1NV Sata 1 Secondary RAID IDE Prefetch ModeNV Sata 1 Primary RAID NV Sata 2 class codeNoteOnboard Parallel Port Parallel Port ModeECP Mode Use DMA On-Chip USBModem Ring On Power-On by AlarmPME Event Wake Up USB Resume from SuspendKB Power on Password Power On by MousePower On by Keyboard AC Back FunctionCurrent VoltageV Vcore / DDR25V / +3.3V / +12V PC Health StatusCase Opened Temp of FAN turn off Default temperature 0oC Current CPU TemperatureCPU Warning Temperature Current CPU/SYSTEM FAN Speed RPMTemp Limit of High Speed Default temperature 60oC Temp Limit of Low Speed Default temperature 20oCTemp Limit of Mid Speed Default temperature 50oC Temp of full FAN Speed Default temperature 70oCLoad Optimized Defaults Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupSelecting the Striping Block Size Using the Define a New Array WindowSelecting the RAID Mode Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting Contact Us Taiwan HeadquartersChina Shanghai