Gigabyte GA-K8NXP-SLI user manual Ircir, USB1 / FUSB2/FUSB3 Front USB Connector

Page 29

15)IR_CIR

Make sure the pin 1 on the IR device is align with pin one the connector. To enable the IR/CIR function, you are required to purchase an optional IR/CIR module. To use IR function only, please connect IR module to Pin1 to Pin5. Be careful with the polarity of the IR/CIR connector. Check the pin assignment carefully while you connect the IR/CIR cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional IR/CIR cable, please contact your local dealer.

 

 

Pin No.

Definition

 

 

1

Power

6

10

2

NC

 

 

3

IRRX

1

5

4

GND

 

 

5

IRTX

 

 

6

NC

 

 

7

CIRRX

 

 

8

+5VSB

 

 

9

CIRTX

 

 

10

NC

English

16)F_ USB1 / F_USB2/F_USB3 (Front USB Connector)

Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you connect the front USB cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional front USB cable, please contact your local dealer.

210

19

Pin No.

Definition

1

Power

2

Power

3

USB DX-

4

USB Dy-

5

USB DX+

6

USB Dy+

7

GND

8

GND

9

No Pin

10

NC

 

 

- 29 -

Hardware Installation

Image 29
Contents GA-K8NXP-SLI Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-K8NXP-SLI Motherboard Layout Block Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerSATA3SII Feature SummaryBios Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards What is K8DPS? Installation of K8DPS Dual Power SystemBefore You Begin Setup of SLI Scalable Link Interface ConfigurationEnabling SLI Mode Graphics card I/O Back Panel Introduction Side Speaker Out Connectors IntroductionRear Speaker Out ATX12V/ATX Power Connector Nbfan Chip Fan Power Connector 5 Cpufan / SYSFAN/ Pwrfan Cooler Fan Power ConnectorIDE1 / IDE2 IDE Connector FDD FDD ConnectorFaudio Front Audio Panel Connector Fpanel Front Panel Jumper Pwrled Cdin CD In ConnectorIrcir USB1 / FUSB2/FUSB3 Front USB ConnectorClrcmos Clear Cmos 17 F11394/F21394 Ieee 1394 ConnectorsBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F2g „ Exit Without Saving „ Set User Password„ Save & Exit Setup IDE Channel 0 Master/Slave IDE Channel 1 Master/Slave TimeFloppy 3 Mode Support for Japan Area Boot Up Floppy Seek Hard Disk Boot PriorityFirst / Second / Third Boot Device Init Display First Password CheckIntegrated Peripherals IDE DMA transfer accessOn-Chip IDE Channel0 On-Chip IDE Channel1IDE Prefetch Mode On-Chip LAN Boot ROMOn-Chip MAC Lan LAN IDE/SATA RAID functionOn-Chip USB Onboard LAN Boot ROMUSB Memory Type USB Keyboard SupportECP Mode Use DMA Parallel Port ModeOnboard Parallel Port CIR Port AddressPME Event Wake Up Power-On by AlarmModem Ring On USB Resume from SuspendAC Back Function Power On By MousePower On By Keyboard PnP/PCI Configurations Current CPU/POWER/SYSTEM FAN Speed RPM Current CPU TemperatureCPU Warning Temperature Current VoltageV Vcore / DDR25V / +3.3V / +12VCPU Frequency Core Power voltage controlCPU Spread Spectrum Pcie ClockDDR voltage control HT-Link voltage controlExit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? Press F9 during powering on the computer. Text Mode F9 For Xpress RecoveryExit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NHow to use Dual Bios and Q-Flash Utility? Flash Bios Method IntroductionWhat is Dual Bios Technology? Boot From Main BIOSDefault, Backup Bios Wide Range Protection DisableDefault, EnableAuto Recovery EnableDefault, Disable Halt On Error DisableDefault, EnableBefore You Begin Method 1 Q-FlashTMUtilityTask menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two Task menu for Q-FlashTMutility FlashTMutility bar Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosSelecting the RAID Mode Using the Define a New Array WindowSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Cd bootdrv Menu Installing the RAID drivers5 2- / 4- / 6- / 8- Channel Audio Function Introduction Introduction of audio connectorsStereo Speakers Connection and Settings Channel Audio Setup English English Auto-detecting Jack-Sensing IntroductionManual setting Troubleshooting English English English English Taiwan Headquarters Contact UsChina Shanghai