Gigabyte GA-K8NXP-SLI Current VoltageV Vcore / DDR25V / +3.3V / +12V, Current CPU Temperature

Page 47

2-6

PC Health Status

 

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

 

 

 

 

PC Health Status

 

 

 

Vcore

 

1.550V

 

Item Help

 

DDR25V

 

2.624V

Menu Level`

 

+3.3V

 

3.360V

 

 

 

+12V

 

11.795V

[Disabled]

 

Current CPU Temperature

38oC

 

Don't monitor

 

Current CPU FAN Speed

3245 RPM

current temperature

 

Current POWER FAN Speed

0

RPM

 

 

 

Current SYSTEM FAN Speed

0

RPM

[60oC-90oC]

 

CPU Warning Temperature

[Disabled]

Alarm when current

 

CPU FAN Fail Warning

[Disabled]

temperature over than

 

CPU Smart FAN Control

[Enabled]

the selected

 

 

 

 

 

temperature

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

 

F5: Previous Values

 

F7: Optimized Defaults

 

 

 

 

 

 

 

 

Current Voltage(V) Vcore / DDR25V / +3.3V / +12V

Detect system's voltage status automatically.

Current CPU Temperature

Detect CPU temperature automatically.

Current CPU/POWER/SYSTEM FAN Speed (RPM)

Detect CPU/Power/System fan speed status automatically.

CPU Warning Temperature

60oC / 140oF

Monitor CPU temperature at 60oC / 140oF.

70oC / 158oF

Monitor CPU temperature at 70oC / 158oF.

80oC / 176oF

Monitor CPU temperature at 80oC / 176oF.

90oC / 194oF

Monitor CPU temperature at 90oC / 194oF.

Disabled

Disable this function. (Default value)

CPU FAN Fail Warning

Disabled

Disable CPU fan fail warning function. (Default value)

Enabled

Enable CPU fan fail warning function.

CPU Smart FAN Control

Disabled

Disable this function.

Enabled

When this function is enabled, CPU fan will run at different speed depending

 

on CPU temperature. Users can adjust the fan speed with Easy Tune

 

based on their requirements. (Default value)

English

- 47 -

BIOS Setup

Image 47
Contents GA-K8NXP-SLI Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-K8NXP-SLI Motherboard Layout Block Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantySATA3SII Feature SummaryBios Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards What is K8DPS? Installation of K8DPS Dual Power SystemBefore You Begin Setup of SLI Scalable Link Interface ConfigurationEnabling SLI Mode Graphics card I/O Back Panel Introduction Side Speaker Out Connectors IntroductionRear Speaker Out ATX12V/ATX Power Connector Nbfan Chip Fan Power Connector 5 Cpufan / SYSFAN/ Pwrfan Cooler Fan Power ConnectorIDE1 / IDE2 IDE Connector FDD FDD ConnectorFaudio Front Audio Panel Connector Fpanel Front Panel Jumper Pwrled Cdin CD In ConnectorIrcir USB1 / FUSB2/FUSB3 Front USB ConnectorClrcmos Clear Cmos 17 F11394/F21394 Ieee 1394 ConnectorsBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F2g „ Exit Without Saving „ Set User Password„ Save & Exit Setup IDE Channel 0 Master/Slave IDE Channel 1 Master/Slave TimeFloppy 3 Mode Support for Japan Area Boot Up Floppy Seek Hard Disk Boot PriorityFirst / Second / Third Boot Device Init Display First Password CheckOn-Chip IDE Channel1 IDE DMA transfer accessIntegrated Peripherals On-Chip IDE Channel0IDE/SATA RAID function On-Chip LAN Boot ROMIDE Prefetch Mode On-Chip MAC Lan LANUSB Keyboard Support Onboard LAN Boot ROMOn-Chip USB USB Memory TypeCIR Port Address Parallel Port ModeECP Mode Use DMA Onboard Parallel PortUSB Resume from Suspend Power-On by AlarmPME Event Wake Up Modem Ring OnAC Back Function Power On By MousePower On By Keyboard PnP/PCI Configurations Current VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM CPU Warning TemperaturePcie Clock Core Power voltage controlCPU Frequency CPU Spread SpectrumDDR voltage control HT-Link voltage controlExit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? Press F9 during powering on the computer. Text Mode F9 For Xpress RecoveryExit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NHow to use Dual Bios and Q-Flash Utility? Flash Bios Method IntroductionWhat is Dual Bios Technology? Halt On Error DisableDefault, Enable Wide Range Protection DisableDefault, EnableBoot From Main BIOSDefault, Backup Bios Auto Recovery EnableDefault, DisableBefore You Begin Method 1 Q-FlashTMUtilityTask menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two Task menu for Q-FlashTMutility FlashTMutility bar Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosAssigning the Disks Using the Define a New Array WindowSelecting the RAID Mode Selecting the Striping Block SizeCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Cd bootdrv Menu Installing the RAID drivers5 2- / 4- / 6- / 8- Channel Audio Function Introduction Introduction of audio connectorsStereo Speakers Connection and Settings Channel Audio Setup English English Auto-detecting Jack-Sensing IntroductionManual setting Troubleshooting English English English English Taiwan Headquarters Contact UsChina Shanghai