Gigabyte GA-K8NXP-SLI user manual 17 F11394/F21394 Ieee 1394 Connectors, Clrcmos Clear Cmos

Page 30

English

17)F1_1394/F2_1394 (IEEE 1394 Connectors)

Serial interface standard set by Institute of Electrical and Electronics Engineers, which has features like high speed, high bandwidth and hot plug. Be careful with the polarity of the IEEE1394 connector. Check the pin assignment carefully while you connect the IEEE1394 cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional IEEE1394 cable, please contact your local dealer. IEEE1394b can approach the

maximum speed to 800Mb/S, but the speed can be achieved only when you use particular

IEEE1394b cable.

 

 

2

16

 

 

 

F2_1394

 

F1_1394

2

10

1

15

Pin No.

Definition

1

9

 

1

Power

 

 

 

Pin No.

Definition

2

Power

3

TPA1+

1

 

TPA0+

 

4

TPA1-

2

 

TPA0-

 

5

GND

3

 

GND

 

6

GND

4

 

GND

 

7

TPB1+

5

 

TPB0+

 

8

TPB1-

6

 

TPB0-

 

9

Power

7

 

No Pin

 

10

Power

8

 

Power

 

11

TPA2+

9

 

Power

 

12

TPA2-

10

 

GND

 

13

GND

 

 

 

 

 

 

14

No Pin

 

 

 

15

TPB2+

 

 

 

16

TPB2-

18)CLR_CMOS (Clear CMOS)

You may clear the CMOS data to its default values by this header. To clear CMOS, temporarily short 1-2 pin. Default doesn't include the jumper to prevent from improper use of this header.

Open: Normal

1

Short: Clear CMOS

1

GA-K8NXP-SLI Motherboard

- 30 -

Image 30
Contents GA-K8NXP-SLI Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NXP-SLI Motherboard Layout Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary SATA3SIIBios Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Installation of K8DPS Dual Power System What is K8DPS?Setup of SLI Scalable Link Interface Configuration Before You BeginEnabling SLI Mode Graphics card I/O Back Panel Introduction Connectors Introduction Rear Speaker OutSide Speaker Out ATX12V/ATX Power Connector 5 Cpufan / SYSFAN/ Pwrfan Cooler Fan Power Connector Nbfan Chip Fan Power ConnectorFDD FDD Connector IDE1 / IDE2 IDE ConnectorFaudio Front Audio Panel Connector Fpanel Front Panel Jumper Cdin CD In Connector PwrledUSB1 / FUSB2/FUSB3 Front USB Connector Ircir17 F11394/F21394 Ieee 1394 Connectors Clrcmos Clear CmosBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F2g „ Set User Password „ Save & Exit Setup„ Exit Without Saving Time IDE Channel 0 Master/Slave IDE Channel 1 Master/SlaveFloppy 3 Mode Support for Japan Area Hard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek Password Check Init Display FirstOn-Chip IDE Channel0 IDE DMA transfer accessIntegrated Peripherals On-Chip IDE Channel1On-Chip MAC Lan LAN On-Chip LAN Boot ROMIDE Prefetch Mode IDE/SATA RAID functionUSB Memory Type Onboard LAN Boot ROMOn-Chip USB USB Keyboard SupportOnboard Parallel Port Parallel Port ModeECP Mode Use DMA CIR Port AddressModem Ring On Power-On by AlarmPME Event Wake Up USB Resume from SuspendPower On By Mouse Power On By KeyboardAC Back Function PnP/PCI Configurations CPU Warning Temperature Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM Current VoltageV Vcore / DDR25V / +3.3V / +12VCPU Spread Spectrum Core Power voltage controlCPU Frequency Pcie ClockHT-Link voltage control DDR voltage controlSave & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Press F9 during powering on the computer. Text ModeRemove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartFlash Bios Method Introduction What is Dual Bios Technology?How to use Dual Bios and Q-Flash Utility? Auto Recovery EnableDefault, Disable Wide Range Protection DisableDefault, EnableBoot From Main BIOSDefault, Backup Bios Halt On Error DisableDefault, EnableMethod 1 Q-FlashTMUtility Before You BeginEntering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen Task menu for Q-FlashTMutility FlashTMutility barCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupSelecting the Striping Block Size Using the Define a New Array WindowSelecting the RAID Mode Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Cd bootdrv MenuIntroduction of audio connectors Stereo Speakers Connection and Settings5 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English English Jack-Sensing Introduction Auto-detectingManual setting Troubleshooting English English English English Contact Us Taiwan HeadquartersChina Shanghai