Gigabyte GA-8ANXP-D Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector, Nbfan Chip Fan Connector

Page 20

English

3/4/5) CPU_FAN / SYS_FAN / PWR_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin(only for CPU_FAN) power connector and possesses a ful-proof connection design.

Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND).

Please remember to connect the power to the cooler to prevent system overheating and failure. Caution!

Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.


1						Pin No.	Definition
						1	GND
	CPU_FAN					1	GND
						2	+12V
						3	Sense
						4	Speed Control
							(Only for CPU_FAN)
1							(Only for CPU_FAN)


SYS_FAN / PWR_FAN

6)NB_FAN (Chip Fan Connector)

If you installed wrong direction, the chip fan will not work. Sometimes will damage the chip fan. (Usually black cable is GND)

1

Pin No.	Definition
1	+12V
2	GND

GA-8ANXP-D Motherboard

- 20 -

Image 20

Contents GA-8ANXP-D Motherboard Copyright Table of Contents Drivers Installation GA-8ANXP-D Motherboard Layout Block Diagram Page Hardware Installation Considerations Prior to InstallationFeature Summary CPUBios Installation of the CPU and Heatsink HT functionality requirement contentInstallation of the Heatsink Installing/Removing Cool-Plus Northbridge Cooling Fan Installation of MemoryDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Side Speaker Out Connectors IntroductionCenter/Subwoofer Speaker Out ATX12V/ATX Power Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector Nbfan Chip Fan ConnectorFDD FDD Connector IDE IDE ConnectorPwrled Fpanel Front Panel Jumper Azaliafp Front Audio Panel Connector Cdin CD In ConnectorUSB1 / FUSB2 / FUSB3 / FUSB4 Front USB Connector 16 F11394/F21394 Ieee 1394 Connector17 IR Clrcmos Clear CmosBATBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F3h „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupTime IDE Channel 0 Master, SlaveFloppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryPassword Check Hard Disk Boot PriorityFirst / Second / Third Boot Device CPU Hyper-Threading Limit Cpuid Max. toOn-Chip Primary PCI IDE Sata RAID / Ahci ModeIntegrated Peripherals On-Chip Sata Mode Pata IDE Set toSata Port 0/2 Set to Sata Port 1/3 Set toOnboard LAN1 Boot ROM LAN1 port Onboard LAN2 Boot ROM LAN2 portUart Mode Select UR2 Duplex ModeParallel Port Mode ECP Mode Use DMAPower On by Ring PME Event Wake UpResume by Alarm Power On by MousePower On by Keyboard KB Power on PasswordPnP/PCI Configurations Current CPU Temperature Current CPU/POWER/SYSTEM FAN Speed RPMCPU Warning Temperature CPU/POWER/SYSEM FAN Fail WarningCPU FAN PIN Type CPU Host Clock Control CPU Clock RatioA.2 CPU Host FrequencyMhz Memory Frequency ForMemory Frequency Mhz Dimm OverVoltage ControlLoad Fail-Safe Defaults Select LanguageLoad Optimized Defaults Set Supervisor/User PasswordSave & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities What is Xpress Recovery ? How to use the Xpress RecoveryF9 For Xpress Recovery Remove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartWhat is Dual Bios Technology? How to use Dual Bios and Q-Flash Utility?Wide Range Protection DisableDefault, Enable Boot From Main BIOSDefault, Backup BiosAuto Recovery EnableDefault, Disable Halt On Error DisableDefault, EnableMethod 1 Q-FlashTMUtility Before You BeginExploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Intel RAID Bios DISK/VOLUME InformationCreate RAID Volume Press Enter under Create RAID Volume to set up RAID128KB Press Enter under the Create Volume item Delete RAID Volume Installing the RAID drivers Introduction of audio connectors Stereo Speakers Connection and SettingsChannel Audio Setup English Step Jack-Sensing Introduction Troubleshooting English English English English English English Contact Us China Shanghai