Gigabyte GA-8ANXP-D user manual Part Two

Page 63

6.Press Del to enter BIOS menu after system reboots. When you are in BIOS menu, move to

Load Fail-Safe Defaults item and press Enter to load BIOS Fail-Safe Defaults. Normally the system redetects all devices after BIOS has been upgraded. Therefore, we highly recommend reloading the BIOS defaults after BIOS has been upgraded.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features

Select Language

Advanced BIOS Features

Load Fail-Safe Defaults

Integrated Peripherals

Load Optimized Defaults

Power Management Setup

Load Fail-Safe Defaults (Y/N)?Set SupervisorY

Password

PnP/PCI Configurations

Set User Password

PC Health Status

Save & Exit Setup

MB Intelligent Tweaker(M.I.T.)

Exit Without Saving

ESC: Quit

F3: Change Language

F8: Dual BIOS/Q-Flash

F10: Save & Exit Setup

 

Time, Date, Hard Disk Type...

 

Press Y on your keyboard to load defaults.

7.Select Save & Exit Setup item to save the settings to CMOS and exit the BIOS menu. System will reboot after you exit the BIOS menu. The procedure is completed.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features

 

Select Language

Advanced BIOS Features

 

Load Fail-Safe Defaults

Integrated Peripherals

 

Load Optimized Defaults

Power Management Setup

Save to CMOS and EXIT (Y/N)?Set SupervisorY

Password

PnP/PCI Configurations

 

Set User Password

PC Health Status

 

Save & Exit Setup

MB Intelligent Tweaker(M.I.T.)

Exit Without Saving

ESC: Quit

 

F3: Change Language

F8: Dual BIOS/Q-Flash

 

F10: Save & Exit Setup

 

 

Time, Date, Hard Disk Type...

 

 

Press Y on your keyboard to save and exit.

Part Two:

 

 

 

Updating BIOS with Q-FlashTMUtility on Single-BIOS Motherboards.

This part guides users of single-BIOS motherboards how to update BIOS using the Q-FlashTMutility.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features

Top Performance

Advanced BIOS Features

Load Fail-Safe Defaults

Integrated Peripherals

Load Optimized Defaults

Power Management Setup

Set Supervisor Password

PnP/PCI Configurations

Set User Password

PC Health Status

Save & Exit Setup

MB Intelligent Tweaker(M.I.T.)

Exit Without Saving

ESC: Quit

F3: Change Language

F8: Q-Flash

F10: Save & Exit Setup

 

Time, Date, Hard Disk Type...

English

- 63 -

Appendix

Image 63
Contents GA-8ANXP-D Motherboard Copyright Table of Contents Drivers Installation GA-8ANXP-D Motherboard Layout Block Diagram Page Considerations Prior to Installation Hardware InstallationCPU Feature SummaryBios HT functionality requirement content Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installing/Removing Cool-Plus Northbridge Cooling FanDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutSide Speaker Out ATX12V/ATX Power Connector Nbfan Chip Fan Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorIDE IDE Connector FDD FDD ConnectorPwrled Fpanel Front Panel Jumper Cdin CD In Connector Azaliafp Front Audio Panel Connector16 F11394/F21394 Ieee 1394 Connector USB1 / FUSB2 / FUSB3 / FUSB4 Front USB ConnectorClrcmos Clear Cmos 17 IRBATBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F3h „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordIDE Channel 0 Master, Slave TimeMemory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onHard Disk Boot Priority First / Second / Third Boot DevicePassword Check Limit Cpuid Max. to CPU Hyper-ThreadingSata RAID / Ahci Mode Integrated PeripheralsOn-Chip Primary PCI IDE Sata Port 1/3 Set to On-Chip Sata ModePata IDE Set to Sata Port 0/2 Set toUR2 Duplex Mode Onboard LAN1 Boot ROM LAN1 portOnboard LAN2 Boot ROM LAN2 port Uart Mode SelectPME Event Wake Up Parallel Port ModeECP Mode Use DMA Power On by RingKB Power on Password Resume by AlarmPower On by Mouse Power On by KeyboardPnP/PCI Configurations CPU/POWER/SYSEM FAN Fail Warning Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM CPU Warning TemperatureCPU FAN PIN Type CPU Clock Ratio A.2CPU Host Clock Control Dimm OverVoltage Control CPU Host FrequencyMhzMemory Frequency For Memory Frequency MhzSelect Language Load Fail-Safe DefaultsSet Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities How to use the Xpress Recovery What is Xpress Recovery ?F9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NHow to use Dual Bios and Q-Flash Utility? What is Dual Bios Technology?Halt On Error DisableDefault, Enable Wide Range Protection DisableDefault, EnableBoot From Main BIOSDefault, Backup Bios Auto Recovery EnableDefault, DisableBefore You Begin Method 1 Q-FlashTMUtilityTask menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionDISK/VOLUME Information Configuring the Intel RAID BiosPress Enter under Create RAID Volume to set up RAID Create RAID Volume128KB Press Enter under the Create Volume item Delete RAID Volume Installing the RAID drivers Stereo Speakers Connection and Settings Introduction of audio connectorsChannel Audio Setup English Step Jack-Sensing Introduction Troubleshooting English English English English English English Contact Us China Shanghai