Gigabyte GA-8ANXP-D user manual Time, IDE Channel 0 Master, Slave

Page 32

English

2-1

Standard CMOS Features

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

 

 

 

 

 

Standard CMOS Features

 

 

 

Date (mm:dd:yy)

 

 

Fri, May 21 2004

Item Help

 

Time (hh:mm:ss)

 

 

 

22:31:24

 

Menu Level`

` IDE Channel 0 Master

 

[None]

 

Change the day, month,

` IDE Channel 0 Slave

 

 

[None]

 

year

 

 

Drive A

 

 

 

[1.44M, 3.5"]

<Week>

 

 

Drive B

 

 

 

[None]

 

Sun. to Sat.

 

Floppy 3 Mode Suport

 

[Disabled]

 

<Month>

 

 

 

 

 

 

 

 

Holt On

 

 

 

[All, But Keyboard]

Jan. to Dec.

 

Base Memory

 

 

 

640K

 

<Day>

 

 

Extended Memory

 

 

511M

 

1 to 31 (or maximum

 

Total Memory

 

 

 

512M

 

allowed in the month)

 

 

 

 

 

 

 

<Year>

 

 

 

 

 

 

 

 

1999 to 2098

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F3: Language

F5: Previous Values

F6: Fail-Save Default

F7: Optimized Defaults

 

 

 

 

 

 

 

 

 

 

Date

 

 

 

 

 

 

 

 

The date format is <week>, <month>, <day>, <year>.

 

 

 

 

Week

 

The week, from Sun to Sat, determined by the BIOS and is display only

 

Month

 

The month, Jan. Through Dec.

 

 

 

 

Day

 

The day, from 1 to 31 (or the maximum allowed in the month)

 

 

Year

 

The year, from 1999 through 2098

 

 

 

Time

The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour military- time clock. For example, 1 p.m. is 13:00:00.

IDE Channel 0 Master, Slave

IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection. IDE Channel 0 Master/Slave IDE Device Setup. You can use one of three methods:

Auto

Allows BIOS to automatically detect IDE devices during POST(default)

None

Select this if no IDE devices are used and the system will skip the automatic

 

detection step and allow for faster system start up.

Manual

User can manually input the correct settings

Access Mode

Use this to set the access mode for the hard drive. The four options are:

 

CHS/LBA/Large/Auto(default:Auto)

Hard drive information should be labeled on the outside drive casing. Enter the appropriate option based on this information.

Cylinder

Number of cylinders

Head

Number of heads

Precomp

Write precomp

Landing Zone

Landing zone

Sector

Number of sectors

If a hard disk has not been installed, select NONE and press <Enter>.

GA-8ANXP-D Motherboard

- 32 -

Image 32
Contents GA-8ANXP-D Motherboard Copyright Table of Contents Drivers Installation GA-8ANXP-D Motherboard Layout Block Diagram Page Hardware Installation Considerations Prior to InstallationFeature Summary CPUBios Installation of the CPU and Heatsink HT functionality requirement contentInstallation of the Heatsink Installing/Removing Cool-Plus Northbridge Cooling Fan Installation of MemoryDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Side Speaker Out Connectors IntroductionCenter/Subwoofer Speaker Out ATX12V/ATX Power Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector Nbfan Chip Fan ConnectorFDD FDD Connector IDE IDE ConnectorPwrled Fpanel Front Panel Jumper Azaliafp Front Audio Panel Connector Cdin CD In ConnectorUSB1 / FUSB2 / FUSB3 / FUSB4 Front USB Connector 16 F11394/F21394 Ieee 1394 Connector17 IR Clrcmos Clear CmosBATBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F3h „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupTime IDE Channel 0 Master, SlaveFloppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryPassword Check Hard Disk Boot PriorityFirst / Second / Third Boot Device CPU Hyper-Threading Limit Cpuid Max. toOn-Chip Primary PCI IDE Sata RAID / Ahci ModeIntegrated Peripherals On-Chip Sata Mode Pata IDE Set toSata Port 0/2 Set to Sata Port 1/3 Set toOnboard LAN1 Boot ROM LAN1 port Onboard LAN2 Boot ROM LAN2 portUart Mode Select UR2 Duplex ModeParallel Port Mode ECP Mode Use DMAPower On by Ring PME Event Wake UpResume by Alarm Power On by MousePower On by Keyboard KB Power on PasswordPnP/PCI Configurations Current CPU Temperature Current CPU/POWER/SYSTEM FAN Speed RPMCPU Warning Temperature CPU/POWER/SYSEM FAN Fail WarningCPU FAN PIN Type CPU Host Clock Control CPU Clock RatioA.2 CPU Host FrequencyMhz Memory Frequency ForMemory Frequency Mhz Dimm OverVoltage ControlLoad Fail-Safe Defaults Select LanguageLoad Optimized Defaults Set Supervisor/User PasswordSave & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities What is Xpress Recovery ? How to use the Xpress RecoveryF9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartWhat is Dual Bios Technology? How to use Dual Bios and Q-Flash Utility?Wide Range Protection DisableDefault, Enable Boot From Main BIOSDefault, Backup BiosAuto Recovery EnableDefault, Disable Halt On Error DisableDefault, EnableMethod 1 Q-FlashTMUtility Before You BeginExploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Intel RAID Bios DISK/VOLUME InformationCreate RAID Volume Press Enter under Create RAID Volume to set up RAID128KB Press Enter under the Create Volume item Delete RAID Volume Installing the RAID drivers Introduction of audio connectors Stereo Speakers Connection and SettingsChannel Audio Setup English Step Jack-Sensing Introduction Troubleshooting English English English English English English Contact Us China Shanghai