Gigabyte GA-8ANXP-D user manual Block Diagram

Page 7

Block Diagram

PCI-ECLK

(100MHz)

LGA775

CPUCLK+/-(200/133MHz)

Processor

Host

Interface

DDRII 600(Note)/533/400MHz DIMM

PCI Express x16

Intel

925X

Dual Channel Memory

3 PCI Express x 1 Ports

MCH

MCHCLK (133/200MHz)

PCI-ECLK

66MHz

(100MHz)

RJ45

33MHz

14.318MHz

Broadcom

48MHz

5751

Dual BIOS

4 Serial ATA

PCI Express x 1 Bus

Intel

4 Serial ATA

PCI Bus

ICH6R

SiI3114

ATA33/66/100 IDE Channels

Marvell

TSB82AA2

8001

TSB81BA3

Floppy

RJ45

IT 8712

LPT Port

IEEE1394b3

OutSpeaker

OutSpeaker

OutSpeaker

MIC Out-Line

In-Line

InSPDIF OutSPDIF

CY7C6564D

CODEC

COM Port

24MHz

PS/2 KB/Mouse

8 USB

2 PCI

Ports

33MHz

Surround Center/Subwoofer Side

3 USB

Ports

PCICLK

(33MHz)

(Note) To use a DDRII 600 memory module on the motherboard, you must install an 800MHz FSB processor and overclock in BIOS.

- 7 -

Image 7

Contents GA-8ANXP-D Motherboard Copyright Table of Contents Drivers Installation GA-8ANXP-D Motherboard Layout Block Diagram Page Considerations Prior to Installation Hardware InstallationCPU Feature SummaryBios HT functionality requirement content Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installing/Removing Cool-Plus Northbridge Cooling FanDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Center/Subwoofer Speaker Out Connectors IntroductionSide Speaker Out ATX12V/ATX Power Connector Nbfan Chip Fan Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorIDE IDE Connector FDD FDD ConnectorPwrled Fpanel Front Panel Jumper Cdin CD In Connector Azaliafp Front Audio Panel Connector16 F11394/F21394 Ieee 1394 Connector USB1 / FUSB2 / FUSB3 / FUSB4 Front USB ConnectorClrcmos Clear Cmos 17 IRBATBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F3h „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordIDE Channel 0 Master, Slave TimeMemory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onFirst / Second / Third Boot Device Hard Disk Boot PriorityPassword Check Limit Cpuid Max. to CPU Hyper-ThreadingIntegrated Peripherals Sata RAID / Ahci ModeOn-Chip Primary PCI IDE Sata Port 1/3 Set to On-Chip Sata ModePata IDE Set to Sata Port 0/2 Set toUR2 Duplex Mode Onboard LAN1 Boot ROM LAN1 portOnboard LAN2 Boot ROM LAN2 port Uart Mode SelectPME Event Wake Up Parallel Port ModeECP Mode Use DMA Power On by RingKB Power on Password Resume by AlarmPower On by Mouse Power On by KeyboardPnP/PCI Configurations CPU/POWER/SYSEM FAN Fail Warning Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM CPU Warning TemperatureCPU FAN PIN Type A.2 CPU Clock RatioCPU Host Clock Control Dimm OverVoltage Control CPU Host FrequencyMhzMemory Frequency For Memory Frequency MhzSelect Language Load Fail-Safe DefaultsSet Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities How to use the Xpress Recovery What is Xpress Recovery ?F9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NHow to use Dual Bios and Q-Flash Utility? What is Dual Bios Technology?Halt On Error DisableDefault, Enable Wide Range Protection DisableDefault, EnableBoot From Main BIOSDefault, Backup Bios Auto Recovery EnableDefault, DisableBefore You Begin Method 1 Q-FlashTMUtilityTask menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionDISK/VOLUME Information Configuring the Intel RAID BiosPress Enter under Create RAID Volume to set up RAID Create RAID Volume128KB Press Enter under the Create Volume item Delete RAID Volume Installing the RAID drivers Stereo Speakers Connection and Settings Introduction of audio connectorsChannel Audio Setup English Step Jack-Sensing Introduction Troubleshooting English English English English English English Contact Us China Shanghai