Gigabyte GA-8ANXP-D user manual Method 1 Q-FlashTMUtility, Before You Begin

Page 59

Method 1 : Q-FlashTMUtility

Q-FlashTMis a BIOS flash utility embedded in Flash ROM. With this utility, users only have to stay in the BIOS menu when they want to update BIOS. Q-FlashTMallows users to flash BIOS without any utility in DOS or

Windows. Using Q-FlashTMindicating no more fooling around with any complicated instructions and operating system since it is in the BIOS menu.

Please note that because updating BIOS has potential risk, please do it with caution!! We are sorry that Gigabyte Technology Co., Ltd is not responsible for damages of system because of incorrect manipulation of updating BIOS to avoid any claims from end-users.

Before You Begin:

Before you start updating BIOS with the Q-FlashTMutility, please follow the steps below first.

1.Download the latest BIOS for your motherboard from Gigabyte's website.

2.Extract the BIOS file downloaded and save the BIOS file (the one with model name.Fxx. For example, 8KNXPU.Fba) to a floppy disk.

3.Reboot your PC and press Del to enter BIOS menu.

The BIOS upgrading guides below are separated into two parts.

If your motherboard has dual-BIOS, please refer to Part One.

If your motherboard has single-BIOS, please refer to Part Two.

Part One:

Updating BIOS with Q-FlashTMUtility on Dual BIOS Motherboards.

Some of Gigabyte motherboards are equipped with dual BIOS. In the BIOS menu of the motherboards supporting Q-Flash and Dual BIOS, the Q-Flash utility and Dual BIOS utility are combined in the same screen. This section only deals with how to use Q-Flash utility.

In the following sections, we take GA-8KNXP Ultra as the example to guide you how to flash BIOS from an older version to the latest version. For example, from Fa3 to Fba.

English

The BIOS file is Fa3 before updating

Award Modular BIOS v6.00PG, An Energy Star Ally Copyright (C) 1984-2003, Award Software, Inc.

Intel i875P AGPset BIOS for 8KNXP Ultra Fa3 Check System Health OK , VCore = 1.5250

Main Processor : Intel Pentium(R) 4 1.6GHz (133x12)

<CPUID : 0F27 Patch ID : 0027>

Memory Testing : 131072K OK

Memory Frequency 266 MHz in Single Channel

Primary Master : FUJITSU MPE3170AT ED-03-08

Primary Slave : None

Secondary Master : CREATIVEDVD-RM DVD1242E BC101

Secondary Slave : None

Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 For Xpress Recovery 08/07/2003-i875P-6A79BG03C-00

- 59 -

Appendix

Image 59
Contents GA-8ANXP-D Motherboard Copyright Table of Contents Drivers Installation GA-8ANXP-D Motherboard Layout Block Diagram Page Considerations Prior to Installation Hardware InstallationCPU Feature SummaryBios HT functionality requirement content Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installing/Removing Cool-Plus Northbridge Cooling FanDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Side Speaker Out Connectors IntroductionCenter/Subwoofer Speaker Out ATX12V/ATX Power Connector Nbfan Chip Fan Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorIDE IDE Connector FDD FDD ConnectorPwrled Fpanel Front Panel Jumper Cdin CD In Connector Azaliafp Front Audio Panel Connector16 F11394/F21394 Ieee 1394 Connector USB1 / FUSB2 / FUSB3 / FUSB4 Front USB ConnectorClrcmos Clear Cmos 17 IRBATBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F3h „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordIDE Channel 0 Master, Slave TimeMemory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onPassword Check Hard Disk Boot PriorityFirst / Second / Third Boot Device Limit Cpuid Max. to CPU Hyper-ThreadingOn-Chip Primary PCI IDE Sata RAID / Ahci ModeIntegrated Peripherals Sata Port 1/3 Set to On-Chip Sata ModePata IDE Set to Sata Port 0/2 Set toUR2 Duplex Mode Onboard LAN1 Boot ROM LAN1 portOnboard LAN2 Boot ROM LAN2 port Uart Mode SelectPME Event Wake Up Parallel Port ModeECP Mode Use DMA Power On by RingKB Power on Password Resume by AlarmPower On by Mouse Power On by KeyboardPnP/PCI Configurations CPU/POWER/SYSEM FAN Fail Warning Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM CPU Warning TemperatureCPU FAN PIN Type CPU Host Clock Control CPU Clock RatioA.2 Dimm OverVoltage Control CPU Host FrequencyMhzMemory Frequency For Memory Frequency MhzSelect Language Load Fail-Safe DefaultsSet Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities How to use the Xpress Recovery What is Xpress Recovery ?F9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NHow to use Dual Bios and Q-Flash Utility? What is Dual Bios Technology?Halt On Error DisableDefault, Enable Wide Range Protection DisableDefault, EnableBoot From Main BIOSDefault, Backup Bios Auto Recovery EnableDefault, DisableBefore You Begin Method 1 Q-FlashTMUtilityTask menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionDISK/VOLUME Information Configuring the Intel RAID BiosPress Enter under Create RAID Volume to set up RAID Create RAID Volume128KB Press Enter under the Create Volume item Delete RAID Volume Installing the RAID drivers Stereo Speakers Connection and Settings Introduction of audio connectorsChannel Audio Setup English Step Jack-Sensing Introduction Troubleshooting English English English English English English Contact Us China Shanghai