Gigabyte GA-8ANXP-D user manual Pwrled

Page 22

English

9)SATA0_SB/SATA1_SB/SATA2_SB/SATA3_SB (Serial ATA Connector, Controlled by ICH6R)

10)SATA0_SII/SATA1_SII/SATA2_SII/SATA3_SII (Serial ATA Connector, Controlled by SiI3114)

Serial ATA can provide 150MB/s transfer rate. Please refer to the BIOS setting for the Serial ATA and install the proper driver in order to work properly.

1

7

Pin No.

Definition

 

SATA_SB

1

GND

(Controlled by ICH6R)

2

TXP

 

 

3

TXN

 

7

4

GND

 

 

5

RXN

 

 

6

RXP

 

 

7

GND

 

1

 

 

 

SATA_SII

 

 

(Controlled by SiI3114)

11)PWR_LED

PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode.

1

Pin No.

Definition

1

MPD+

2

MPD-

3

MPD-

 

 

GA-8ANXP-D Motherboard

- 22 -

Image 22
Contents GA-8ANXP-D Motherboard Copyright Table of Contents Drivers Installation GA-8ANXP-D Motherboard Layout Block Diagram Page Hardware Installation Considerations Prior to InstallationFeature Summary CPUBios Installation of the CPU and Heatsink HT functionality requirement contentInstallation of the Heatsink Installing/Removing Cool-Plus Northbridge Cooling Fan Installation of MemoryDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Center/Subwoofer Speaker Out Connectors IntroductionSide Speaker Out ATX12V/ATX Power Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector Nbfan Chip Fan ConnectorFDD FDD Connector IDE IDE ConnectorPwrled Fpanel Front Panel Jumper Azaliafp Front Audio Panel Connector Cdin CD In ConnectorUSB1 / FUSB2 / FUSB3 / FUSB4 Front USB Connector 16 F11394/F21394 Ieee 1394 Connector17 IR Clrcmos Clear CmosBATBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F3h „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupTime IDE Channel 0 Master, SlaveHalt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Hard Disk Boot PriorityPassword Check CPU Hyper-Threading Limit Cpuid Max. toIntegrated Peripherals Sata RAID / Ahci ModeOn-Chip Primary PCI IDE Sata Port 0/2 Set to On-Chip Sata ModePata IDE Set to Sata Port 1/3 Set toUart Mode Select Onboard LAN1 Boot ROM LAN1 portOnboard LAN2 Boot ROM LAN2 port UR2 Duplex ModePower On by Ring Parallel Port ModeECP Mode Use DMA PME Event Wake UpPower On by Keyboard Resume by AlarmPower On by Mouse KB Power on PasswordPnP/PCI Configurations CPU Warning Temperature Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM CPU/POWER/SYSEM FAN Fail WarningCPU FAN PIN Type A.2 CPU Clock RatioCPU Host Clock Control Memory Frequency Mhz CPU Host FrequencyMhzMemory Frequency For Dimm OverVoltage ControlLoad Fail-Safe Defaults Select LanguageLoad Optimized Defaults Set Supervisor/User PasswordSave & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities What is Xpress Recovery ? How to use the Xpress RecoveryF9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartWhat is Dual Bios Technology? How to use Dual Bios and Q-Flash Utility?Auto Recovery EnableDefault, Disable Wide Range Protection DisableDefault, EnableBoot From Main BIOSDefault, Backup Bios Halt On Error DisableDefault, EnableMethod 1 Q-FlashTMUtility Before You BeginEntering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Intel RAID Bios DISK/VOLUME InformationCreate RAID Volume Press Enter under Create RAID Volume to set up RAID128KB Press Enter under the Create Volume item Delete RAID Volume Installing the RAID drivers Introduction of audio connectors Stereo Speakers Connection and SettingsChannel Audio Setup English Step Jack-Sensing Introduction Troubleshooting English English English English English English Contact Us China Shanghai