Gigabyte GA-8ANXP-D user manual Delete RAID Volume

Page 73

After the completion, you will see the detailed information about the RAID, such as RAID level, disk block size, disk name and disk capacity, etc.

Intel(R) Application Accelerator RAID Option ROM v4.0.6180

Copyright(C) 2003-04 Intel Corporation. All Rights Reversed.

[ MAIN MENU ]

1.Create RAID Volume

2.Delete RAID Volume

3.Reset Disks to Non-RAID

4.Exit

 

 

[ DISK/VOLUME INFORMATION ]

 

 

RAID Volumes :

 

 

 

 

 

ID

Name

Level

Strip

Size

Status

Bootable

0

RAID_Volume0

RAID(Stripe)

128KB

223.5GB

Normal

Yes

Physical Disks :

 

 

 

 

 

Port

Driver Model

Serial #

 

Size

Type/Status(Vol ID)

0

ST3120026AS

3JT354CP

 

111.7GB

Member Disk(0)

1

ST3120026AS

3JT329JX

 

111.7GB

Member Disk(0)

 

[ ]-Select

[ESC]-Exit

 

[ENTER]-Select Menu

Delete RAID Volume

If you want to delete a RAID volume, please select the Delete RAID Volume option. Press Enter key and follow the instructions on the screen.

Intel(R) Application Accelerator RAID Option ROM v4.0.6180

Copyright(C) 2003-04 Intel Corporation. All Rights Reversed.

[ MAIN MENU ]

1.Create RAID Volume

2.Delete RAID Volume

3.Reset Disks to Non-RAID

4.Exit

 

 

[ DISK/VOLUME INFORMATION ]

 

 

RAID Volumes :

 

 

 

 

 

ID

Name

Level

Strip

Size

Status

Bootable

0

RAID_Volume0

RAID(Stripe)

128KB

223.5GB

Normal

Yes

Physical Disks :

 

 

 

 

 

Port

Driver Model

Serial #

 

Size

Type/Status(Vol ID)

0

ST3120026AS

3JT354CP

 

111.7GB

Member Disk(0)

1

ST3120026AS

3JT329JX

 

111.7GB

Member Disk(0)

 

[ ]-Select

[ESC]-Exit

 

[ENTER]-Select Menu

English

- 73 -

Appendix

Image 73
Contents GA-8ANXP-D Motherboard Copyright Table of Contents Drivers Installation GA-8ANXP-D Motherboard Layout Block Diagram Page Considerations Prior to Installation Hardware InstallationCPU Feature SummaryBios HT functionality requirement content Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installing/Removing Cool-Plus Northbridge Cooling FanDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Center/Subwoofer Speaker Out Connectors IntroductionSide Speaker Out ATX12V/ATX Power Connector Nbfan Chip Fan Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorIDE IDE Connector FDD FDD ConnectorPwrled Fpanel Front Panel Jumper Cdin CD In Connector Azaliafp Front Audio Panel Connector16 F11394/F21394 Ieee 1394 Connector USB1 / FUSB2 / FUSB3 / FUSB4 Front USB ConnectorClrcmos Clear Cmos 17 IRBATBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F3h „ Set Supervisor Password „ Load Optimized Defaults„ Set User Password „ Save & Exit SetupIDE Channel 0 Master, Slave TimeDrive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryFirst / Second / Third Boot Device Hard Disk Boot PriorityPassword Check Limit Cpuid Max. to CPU Hyper-ThreadingIntegrated Peripherals Sata RAID / Ahci ModeOn-Chip Primary PCI IDE Pata IDE Set to On-Chip Sata ModeSata Port 0/2 Set to Sata Port 1/3 Set toOnboard LAN2 Boot ROM LAN2 port Onboard LAN1 Boot ROM LAN1 portUart Mode Select UR2 Duplex ModeECP Mode Use DMA Parallel Port ModePower On by Ring PME Event Wake UpPower On by Mouse Resume by AlarmPower On by Keyboard KB Power on PasswordPnP/PCI Configurations Current CPU/POWER/SYSTEM FAN Speed RPM Current CPU TemperatureCPU Warning Temperature CPU/POWER/SYSEM FAN Fail WarningCPU FAN PIN Type A.2 CPU Clock RatioCPU Host Clock Control Memory Frequency For CPU Host FrequencyMhzMemory Frequency Mhz Dimm OverVoltage ControlSelect Language Load Fail-Safe DefaultsSet Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities How to use the Xpress Recovery What is Xpress Recovery ?F9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NHow to use Dual Bios and Q-Flash Utility? What is Dual Bios Technology?Boot From Main BIOSDefault, Backup Bios Wide Range Protection DisableDefault, EnableAuto Recovery EnableDefault, Disable Halt On Error DisableDefault, EnableBefore You Begin Method 1 Q-FlashTMUtilityTask menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionDISK/VOLUME Information Configuring the Intel RAID BiosPress Enter under Create RAID Volume to set up RAID Create RAID Volume128KB Press Enter under the Create Volume item Delete RAID Volume Installing the RAID drivers Stereo Speakers Connection and Settings Introduction of audio connectorsChannel Audio Setup English Step Jack-Sensing Introduction Troubleshooting English English English English English English Contact Us China Shanghai