Gigabyte GA-8ANXP-D user manual Jack-Sensing Introduction

Page 79

Jack-Sensing Introduction

Jack-Sensing provides audio connectors error-detection function.

Install Microsoft DirectX8.1 or later version before to enable Jack-Sensing support for Windows 2000.

After you install an audio device, a screen of a list would pop up from the audio software for you to choose the type of device you installed.

If you have connected your device to the wrong jack, the Jack-Sensing function would indicate the correct jack for your device and you can reconnect the device to the correct jack following the arrow instruction.

The correct icon for audio device will be displayed after the reinstallation.

English

- 79 -

Appendix

Page 78 Page 80
Image 79
Page 78 Page 80
Contents GA-8ANXP-D Motherboard Copyright Table of Contents Drivers Installation GA-8ANXP-D Motherboard Layout Block Diagram Page Considerations Prior to Installation Hardware InstallationCPU Feature SummaryBios HT functionality requirement content Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installing/Removing Cool-Plus Northbridge Cooling FanDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Center/Subwoofer Speaker Out Connectors IntroductionSide Speaker Out ATX12V/ATX Power Connector Nbfan Chip Fan Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorIDE IDE Connector FDD FDD ConnectorPwrled Fpanel Front Panel Jumper Cdin CD In Connector Azaliafp Front Audio Panel Connector16 F11394/F21394 Ieee 1394 Connector USB1 / FUSB2 / FUSB3 / FUSB4 Front USB ConnectorClrcmos Clear Cmos 17 IRBATBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F3h „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordIDE Channel 0 Master, Slave TimeMemory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onFirst / Second / Third Boot Device Hard Disk Boot PriorityPassword Check Limit Cpuid Max. to CPU Hyper-ThreadingIntegrated Peripherals Sata RAID / Ahci ModeOn-Chip Primary PCI IDE Sata Port 1/3 Set to On-Chip Sata ModePata IDE Set to Sata Port 0/2 Set toUR2 Duplex Mode Onboard LAN1 Boot ROM LAN1 portOnboard LAN2 Boot ROM LAN2 port Uart Mode SelectPME Event Wake Up Parallel Port ModeECP Mode Use DMA Power On by RingKB Power on Password Resume by AlarmPower On by Mouse Power On by KeyboardPnP/PCI Configurations CPU/POWER/SYSEM FAN Fail Warning Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM CPU Warning TemperatureCPU FAN PIN Type A.2 CPU Clock RatioCPU Host Clock Control Dimm OverVoltage Control CPU Host FrequencyMhzMemory Frequency For Memory Frequency MhzSelect Language Load Fail-Safe DefaultsSet Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities How to use the Xpress Recovery What is Xpress Recovery ?F9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NHow to use Dual Bios and Q-Flash Utility? What is Dual Bios Technology?Halt On Error DisableDefault, Enable Wide Range Protection DisableDefault, EnableBoot From Main BIOSDefault, Backup Bios Auto Recovery EnableDefault, DisableBefore You Begin Method 1 Q-FlashTMUtilityTask menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionDISK/VOLUME Information Configuring the Intel RAID BiosPress Enter under Create RAID Volume to set up RAID Create RAID Volume128KB Press Enter under the Create Volume item Delete RAID Volume Installing the RAID drivers Stereo Speakers Connection and Settings Introduction of audio connectorsChannel Audio Setup English Step Jack-Sensing Introduction Troubleshooting English English English English English English Contact Us China Shanghai
Top Page Image Contents