Gigabyte GA-8ANXP-D Entering the Q-FlashTMutility, Task menu for Dual Bios utility, Action bar

Page 60

English

Entering the Q-FlashTMutility:

Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Select Language
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Set Supervisor Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Dual BIOS/Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

Step 2: Press F8 button on your keyboard and then Y button to enter the Dual BIOS/Q-Flash utility.

Exploring the Q-FlashTM / Dual BIOS utility screen

The Q-Flash / Dual BIOS utility screen consists of the following key components.

Task menu for Dual BIOS utility

Task menu for Q-FlashTMutility

									Dual BIOS utility bar
			Dual BIOS Utility
			Dual BIOS Utility

		Boot From		Main Bios
		Main ROM Type/Size		SST 49LF003A		512K
		Backup ROM Type/Size		SST 49LF003A		512K
		Wide Range Protection		Disable
			Boot From	Main Bios
			Auto Recovery	Enable
			Halt On Error	Disable
			Copy Main ROM Data to Backup
			Load Default Settings
			Save Settings to CMOS						Q-FlashTMutility title

			Q-Flash Utility
			Q-Flash Utility
			Load Main BIOS from Floppy						bar
			Load Backup BIOS from Floppy						bar
			Save Main BIOS to Floppy
			Save Backup BIOS to Floppy						Action bar
			Save Backup BIOS to Floppy
		Enter : Run	:Move	ESC:Reset	F10:Power Off
		Enter : Run	:Move	ESC:Reset	F10:Power Off

Task menu for Dual BIOS utility:

Contains the names of eight tasks and two item showing information about the BIOS ROM type. Blocking a task and pressing Enter key on your keyboard to enable execution of the task.

Task menu for Q-Flash utility:

Contains the names of four tasks. Blocking a task and pressing Enter key on your keyboard to enable execu- tion of the task.

Action bar:

Contains the names of four actions needed to operate the Q-Flash/Dual BIOS utility. Pressing the buttons mentioned on your keyboards to perform these actions.

GA-8ANXP-D Motherboard

- 60 -

Image 60

Contents GA-8ANXP-D Motherboard Copyright Table of Contents Drivers Installation GA-8ANXP-D Motherboard Layout Block Diagram Page Hardware Installation Considerations Prior to InstallationFeature Summary CPUBios Installation of the CPU and Heatsink HT functionality requirement contentInstallation of the Heatsink Installing/Removing Cool-Plus Northbridge Cooling Fan Installation of MemoryDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutSide Speaker Out ATX12V/ATX Power Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector Nbfan Chip Fan ConnectorFDD FDD Connector IDE IDE ConnectorPwrled Fpanel Front Panel Jumper Azaliafp Front Audio Panel Connector Cdin CD In ConnectorUSB1 / FUSB2 / FUSB3 / FUSB4 Front USB Connector 16 F11394/F21394 Ieee 1394 Connector17 IR Clrcmos Clear CmosBATBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F3h „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupTime IDE Channel 0 Master, SlaveFloppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryHard Disk Boot Priority First / Second / Third Boot DevicePassword Check CPU Hyper-Threading Limit Cpuid Max. toSata RAID / Ahci Mode Integrated PeripheralsOn-Chip Primary PCI IDE On-Chip Sata Mode Pata IDE Set toSata Port 0/2 Set to Sata Port 1/3 Set toOnboard LAN1 Boot ROM LAN1 port Onboard LAN2 Boot ROM LAN2 portUart Mode Select UR2 Duplex ModeParallel Port Mode ECP Mode Use DMAPower On by Ring PME Event Wake UpResume by Alarm Power On by MousePower On by Keyboard KB Power on PasswordPnP/PCI Configurations Current CPU Temperature Current CPU/POWER/SYSTEM FAN Speed RPMCPU Warning Temperature CPU/POWER/SYSEM FAN Fail WarningCPU FAN PIN Type CPU Clock Ratio A.2CPU Host Clock Control CPU Host FrequencyMhz Memory Frequency ForMemory Frequency Mhz Dimm OverVoltage ControlLoad Fail-Safe Defaults Select LanguageLoad Optimized Defaults Set Supervisor/User PasswordSave & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities What is Xpress Recovery ? How to use the Xpress RecoveryF9 For Xpress Recovery Remove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartWhat is Dual Bios Technology? How to use Dual Bios and Q-Flash Utility?Wide Range Protection DisableDefault, Enable Boot From Main BIOSDefault, Backup BiosAuto Recovery EnableDefault, Disable Halt On Error DisableDefault, EnableMethod 1 Q-FlashTMUtility Before You BeginExploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Intel RAID Bios DISK/VOLUME InformationCreate RAID Volume Press Enter under Create RAID Volume to set up RAID128KB Press Enter under the Create Volume item Delete RAID Volume Installing the RAID drivers Introduction of audio connectors Stereo Speakers Connection and SettingsChannel Audio Setup English Step Jack-Sensing Introduction Troubleshooting English English English English English English Contact Us China Shanghai