Gigabyte GA-8I865PEM-775 user manual IDE1 / IDE2 IDE Connector, SATA0 / SATA1 Serial ATA Connector

Page 20

English

6)IDE1 / IDE2 (IDE Connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device).

40

39

2

1

7)SATA0 / SATA1 (Serial ATA Connector)

Serial ATA can provide 150MB/s transfer rate. Please refer to the BIOS setting for the Serial ATA and install the proper driver in order to work properly.

			Pin No.	Definition
	7	1	1	GND
	7	1	2	TXP
			2	TXP
			3	TXN
			4	GND
			5	RXN
			6	RXP
			7	GND

GA-8I865PEM-775 Motherboard

- 20 -

Image 20

Contents GA-8I865PEM-775 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation 8I865PEM-775 Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUInstallation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorBATBattery PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSpdif Spdif Out Connector USB1 / FUSB2 Front USB ConnectorComb Comb Connector 16 IRClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E1 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Standard Cmos FeaturesTime Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Limit Cpuid Max. toNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteSata Port1 configure as Integrated PeripheralsOnboard LAN Boot ROM Uart Mode SelectUSB Controller USB 2.0 ControllerUR2 Duplex Mode Parallel Port ModeECP Mode Use DMA Onboard Parallel portPower Management Setup AC Back FunctionPME Event Wake Up ModemRingOn/WakeOnLanPower on Function PnP/PCI ConfigurationsResume by Alarm Current CPU/SYSTEM FAN Speed RPM Current CPU/System TemperatureCurrent VoltageV Vcore / DDR25V / +3.3V / +5V / +12V Frequency/Voltage Control CPU Clock RatioMemory Frequency For Memory Frequency MhzLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 3 2- / 4- / 5.1- Channel Audio Function IntroductionChannel Audio Setup English Spdif Output Device Optional Device Troubleshooting English English English English English Contact Us Taiwan HeadquartersChina Shanghai