Gigabyte GA-8I865PEM-775 user manual „ Load Optimized Defaults, „ Set Supervisor Password

Page 29

„Load Optimized Defaults

Optimized Defaults indicates the value of the system parameters which the system would be in best performance configuration.

„Set Supervisor Password

Change, set, or disable password. It allows you to limit access to the system and Setup, or just to Setup.

„Set User Password

Change, set, or disable password. It allows you to limit access to the system.

„Save & Exit Setup

Save CMOS value settings to CMOS and exit setup.

„Exit Without Saving

Abandon all CMOS value changes and exit setup.

English

- 29 -

BIOS Setup

Image 29
Contents GA-8I865PEM-775 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation 8I865PEM-775 Block Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryInstallation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorPwrled BATBatteryFpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorUSB1 / FUSB2 Front USB Connector Spdif Spdif Out Connector16 IR Comb Comb ConnectorClrcmos Clear Cmos Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E1 „ Set Supervisor Password „ Load Optimized Defaults„ Set User Password „ Save & Exit SetupIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Standard Cmos FeaturesTime Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckLimit Cpuid Max. to CPU Hyper-ThreadingNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteIntegrated Peripherals Sata Port1 configure asUart Mode Select Onboard LAN Boot ROMUSB Controller USB 2.0 ControllerParallel Port Mode UR2 Duplex ModeECP Mode Use DMA Onboard Parallel portAC Back Function Power Management SetupPME Event Wake Up ModemRingOn/WakeOnLanPower on Function PnP/PCI ConfigurationsResume by Alarm Current CPU/SYSTEM FAN Speed RPM Current CPU/System TemperatureCurrent VoltageV Vcore / DDR25V / +3.3V / +5V / +12V CPU Clock Ratio Frequency/Voltage ControlMemory Frequency For Memory Frequency MhzLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish 3 2- / 4- / 5.1- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English Spdif Output Device Optional Device Troubleshooting English English English English English Taiwan Headquarters Contact UsChina Shanghai