Gigabyte GA-8I865PEM-775 user manual Block Diagram

Page 7

Block Diagram

LGA775

CPUCLK+/-(133/200MHz)

Processor

AGP 8X/4X

Host

Interface

AGPCLK

DDR 400/333/266MHz DIMM

Intel

Dual Channel Memory

(66MHz)

865PE

HCLK (133/200MHz)

MCH

MCHCLK (66MHz)

		66MHz
		33MHz
		14.318MHz
		48MHz
		BIOS
	PCI Bus	2 Serial ATA
	Intel	2 Serial ATA
	ICH5	ATA33/66/100
	Marvell	ATA33/66/100
	Marvell	IDE Channels
	8001	IDE Channels
	8001
	RJ45	Floppy
	RJ45
		LPT Port
		LPC47M997
	CODEC	COM Port
	CODEC
		PS/2 KB/Mouse

				8 USB	14.318MHz
	3 PCI		MIC Out-Line Line-In	8 USB	14.318MHz
			MIC Out-Line Line-In	Ports	33MHz
				Ports	33MHz

PCICLK (33MHz)

- 7 -

Image 7

Contents GA-8I865PEM-775 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation 8I865PEM-775 Block Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryInstallation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorPwrled BATBatteryFpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorUSB1 / FUSB2 Front USB Connector Spdif Spdif Out Connector16 IR Comb Comb ConnectorClrcmos Clear Cmos Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E1 „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordTime Standard Cmos FeaturesIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Memory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceCPU Enhanced Halt C1E Note CPU Hyper-ThreadingLimit Cpuid Max. to No-Execute Memory Protect NoteIntegrated Peripherals Sata Port1 configure asUSB 2.0 Controller Onboard LAN Boot ROMUart Mode Select USB ControllerOnboard Parallel port UR2 Duplex ModeParallel Port Mode ECP Mode Use DMAModemRingOn/WakeOnLan Power Management SetupAC Back Function PME Event Wake UpResume by Alarm PnP/PCI ConfigurationsPower on Function Current VoltageV Vcore / DDR25V / +3.3V / +5V / +12V Current CPU/System TemperatureCurrent CPU/SYSTEM FAN Speed RPM Memory Frequency Mhz Frequency/Voltage ControlCPU Clock Ratio Memory Frequency ForLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities Xpress Recovery IntroductionWhat is Xpress Recovery ? How to use the Xpress RecoveryF9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish 3 2- / 4- / 5.1- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English Spdif Output Device Optional Device Troubleshooting English English English English English Taiwan Headquarters Contact UsChina Shanghai