Gigabyte GA-8I865PEM-775 user manual F9 For Xpress Recovery

Page 50

English

2.Press F9 during powering on the computer. (Text Mode) Press F9 during powering on the computer .

Award Modular BIOS v6.00PG, An Energy Star Al ly Copyright (C) 1984-2004, Award Software, Inc.

Intel 865PE AGPSet BIOS for 8IPE1000MT F1 Check System Health OK

.

.

.

Press DEL to enter SETUP / Q-Flash, F9 For Xpress Recovery 08/16/2002-I845GE-6A69YG01C-00

F9 For Xpress Recovery

Xpress Recovery V1.0 (C) Copy Right 2003. GIGABYTE Technology CO. , Ltd.
1.	Execute Backup Utility
2.	Execute Restore Utility
3. Remove Backup Image
4.	Set Password
5.	Exit and Restart

1.If you have already entered Xpress Recovery by booting from the CD-ROM, you can enter Xpress Recovery in the future by pressing the F9 key.

2.System storage capacity as well as drive reading/writing speed will affect backup speed.

3.It is recommended that Xpress Recovery be immediately installed after OS and all required driver and software installations are complete.

GA-8I865PEM-775 Motherboard

- 50 -

Image 50

Contents GA-8I865PEM-775 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation 8I865PEM-775 Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUInstallation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorBATBattery PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSpdif Spdif Out Connector USB1 / FUSB2 Front USB ConnectorComb Comb Connector 16 IRClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E1 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Standard Cmos FeaturesTime Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckNo-Execute Memory Protect Note CPU Hyper-ThreadingLimit Cpuid Max. to CPU Enhanced Halt C1E NoteSata Port1 configure as Integrated PeripheralsUSB Controller Onboard LAN Boot ROMUart Mode Select USB 2.0 ControllerECP Mode Use DMA UR2 Duplex ModeParallel Port Mode Onboard Parallel portPME Event Wake Up Power Management SetupAC Back Function ModemRingOn/WakeOnLanPower on Function PnP/PCI ConfigurationsResume by Alarm Current CPU/SYSTEM FAN Speed RPM Current CPU/System TemperatureCurrent VoltageV Vcore / DDR25V / +3.3V / +5V / +12V Memory Frequency For Frequency/Voltage ControlCPU Clock Ratio Memory Frequency MhzLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 3 2- / 4- / 5.1- Channel Audio Function IntroductionChannel Audio Setup English Spdif Output Device Optional Device Troubleshooting English English English English English Contact Us Taiwan HeadquartersChina Shanghai