Gigabyte GA-8I865PEM-775 user manual Part Two

Page 56

English

6.Press Del to enter BIOS menu after system reboots. When you are in BIOS menu, move to

Load Fail-Safe Defaults item and press Enter to load BIOS Fail-Safe Defaults. Normally the system redetects all devices after BIOS has been upgraded. Therefore, we highly recommend reloading the BIOS defaults after BIOS has been upgraded.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Select Language
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Load Fail-Safe Defaults (Y/N)?Set SupervisorY	Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Dual BIOS/Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

Press Y on your keyboard to load defaults.

7.Select Save & Exit Setup item to save the settings to CMOS and exit the BIOS menu. System will reboot after you exit the BIOS menu. The procedure is completed.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features		Select Language
Advanced BIOS Features		Load Fail-Safe Defaults
Integrated Peripherals		Load Optimized Defaults
Power Management Setup	Save to CMOS and EXIT (Y/N)?Set SupervisorY		Password
PnP/PCI Configurations		Set User Password
PC Health Status		Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)		Exit Without Saving
ESC: Quit		F3: Change Language
F8: Dual BIOS/Q-Flash		F10: Save & Exit Setup
		Time, Date, Hard Disk Type...
	Press Y on your keyboard to save and exit.
Part Two:

Updating BIOS with Q-FlashTMUtility on Single-BIOS Motherboards.

This part guides users of single-BIOS motherboards how to update BIOS using the Q-FlashTMutility.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Top Performance
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Set Supervisor Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

GA-8I865PEM-775 Motherboard

- 56 -

Image 56

Contents GA-8I865PEM-775 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation 8I865PEM-775 Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUInstallation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorBATBattery PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSpdif Spdif Out Connector USB1 / FUSB2 Front USB ConnectorComb Comb Connector 16 IRClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E1 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Standard Cmos FeaturesTime Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Limit Cpuid Max. toNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteSata Port1 configure as Integrated PeripheralsOnboard LAN Boot ROM Uart Mode SelectUSB Controller USB 2.0 ControllerUR2 Duplex Mode Parallel Port ModeECP Mode Use DMA Onboard Parallel portPower Management Setup AC Back FunctionPME Event Wake Up ModemRingOn/WakeOnLanPower on Function PnP/PCI ConfigurationsResume by Alarm Current CPU/SYSTEM FAN Speed RPM Current CPU/System TemperatureCurrent VoltageV Vcore / DDR25V / +3.3V / +5V / +12V Frequency/Voltage Control CPU Clock RatioMemory Frequency For Memory Frequency MhzLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 3 2- / 4- / 5.1- Channel Audio Function IntroductionChannel Audio Setup English Spdif Output Device Optional Device Troubleshooting English English English English English Contact Us Taiwan HeadquartersChina Shanghai