Gigabyte GA-8I865PEM-775 user manual Pwrled, BATBattery

Page 21

8)PWR_LED

PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode.

	Pin No.	Definition
1	1	MPD+
	2	MPD-
	3	MPD-

9) BAT(Battery)

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions.

If you want to erase CMOS...

1. Turn OFF the computer and unplug the power cord.

2. Remove the battery, wait for 30 seconds.

3. Re-install the battery.

4. Plug the power cord and turn ON the computer.

English

- 21 -

Hardware Installation

Image 21

Contents GA-8I865PEM-775 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation 8I865PEM-775 Block Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryInstallation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorPwrled BATBatteryFpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorUSB1 / FUSB2 Front USB Connector Spdif Spdif Out Connector16 IR Comb Comb ConnectorClrcmos Clear Cmos Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E1 „ Set Supervisor Password „ Load Optimized Defaults„ Set User Password „ Save & Exit SetupStandard Cmos Features TimeIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckLimit Cpuid Max. to CPU Hyper-ThreadingNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteIntegrated Peripherals Sata Port1 configure asUart Mode Select Onboard LAN Boot ROMUSB Controller USB 2.0 ControllerParallel Port Mode UR2 Duplex ModeECP Mode Use DMA Onboard Parallel portAC Back Function Power Management SetupPME Event Wake Up ModemRingOn/WakeOnLanPnP/PCI Configurations Resume by AlarmPower on Function Current CPU/System Temperature Current VoltageV Vcore / DDR25V / +3.3V / +5V / +12VCurrent CPU/SYSTEM FAN Speed RPM CPU Clock Ratio Frequency/Voltage ControlMemory Frequency For Memory Frequency MhzLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish 3 2- / 4- / 5.1- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English Spdif Output Device Optional Device Troubleshooting English English English English English Taiwan Headquarters Contact UsChina Shanghai