Gigabyte GA-8I865PEM-775 Frequency/Voltage Control, CPU Clock Ratio, Memory Frequency For

Page 40

English

2-7

Frequency/Voltage Control

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

 

 

 

 

Frequency/Voltage Control

 

 

 

CPU Clock Ratio

[15X]

 

 

Item Help

 

Memory Frequency For

[Auto]

 

Menu Level`

 

Memory Frequency (Mhz)

266

 

Set CPU Ratio if CPU

 

 

 

 

 

 

 

 

 

 

Ratio is unclocked

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Safe Defaults

 

F7: Optimized Defaults

 

 

 

 

 

 

 

Incorrect using these features may cause your system broken. For power end-user use only.

CPU Clock Ratio

This setup option will automatically assign by CPU detection.

The option will display "Locked" and read only if the CPU ratio is not changeable.

Memory Frequency For

Wrong frequency may make system can't boot, clear CMOS to overcome wrong frequency issue. for FSB(Front Side Bus) frequency=533MHz,

2.0

Memory Frequency = Host clock x 2.

2.5

Memory Frequency = Host clock x 2.5.

Auto

Set Memory frequency by DRAM SPD data. (Default value)

for FSB(Front Side Bus) frequency=800MHz,

1.33

Memory Frequency = Host clock x 1.33.

1.66

Memory Frequency = Host clock x 1.66.

2.0

Memory Frequency = Host clock x 2.

Auto

Set Memory frequency by DRAM SPD data. (Default value)

Memory Frequency (Mhz)

The values depend on "Memory Frequency For" item.

GA-8I865PEM-775 Motherboard

- 40 -

Image 40
Contents GA-8I865PEM-775 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation 8I865PEM-775 Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUInstallation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorBATBattery PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSpdif Spdif Out Connector USB1 / FUSB2 Front USB ConnectorComb Comb Connector 16 IRClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E1 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupTime Standard Cmos FeaturesIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Limit Cpuid Max. toNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteSata Port1 configure as Integrated PeripheralsOnboard LAN Boot ROM Uart Mode SelectUSB Controller USB 2.0 ControllerUR2 Duplex Mode Parallel Port ModeECP Mode Use DMA Onboard Parallel portPower Management Setup AC Back FunctionPME Event Wake Up ModemRingOn/WakeOnLanResume by Alarm PnP/PCI ConfigurationsPower on Function Current VoltageV Vcore / DDR25V / +3.3V / +5V / +12V Current CPU/System TemperatureCurrent CPU/SYSTEM FAN Speed RPM Frequency/Voltage Control CPU Clock RatioMemory Frequency For Memory Frequency MhzLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 3 2- / 4- / 5.1- Channel Audio Function IntroductionChannel Audio Setup English Spdif Output Device Optional Device Troubleshooting English English English English English Contact Us Taiwan HeadquartersChina Shanghai