ATTO Technology 1550D operation manual Alphabetical CLI command explanations

Page 35

Command

Default

Example

 

 

 

TailEventLog

 

taileventlog

Time

00:00:00

set time 03:32:30

TimeZone

EST

set timezone pst

Username

root

set username barbara

VerboseMode

enabled

set verbosemode disabled

VirtualDriveResponse

disabled

get virtualdriveresponse

VLAN

 

set vlan dp1 5 alpha1

Alphabetical CLI command explanations

AccessControl

Controls access on a target node. Access to the target node is keyed to the iSCSI qualified name of listed initiators.

Note

AccessControl cannot be used with iSNS.

AutoMapOnBoot

Regulates automatic device detection and mapping (AutoMap) at startup.

Default: enabled

set AutoMapOnBoot [enabled disabled] get AutoMapOnBoot

Default: disabled on the default node; enabled on all other nodes

set AccessControl [default Target Name] [enabled disabled]

get AccessControl [default Target Name]

AccessEntry

Allows the addition or deletion of an initiator entry from the access control list of a target node. The initiator name must be formatted as an iSCSI qualified name and must be between 1 to 223 characters, is case sensitive and cannot be all.

Default: default all

set AccessEntry [default Target Name discovery] [Initiator Name <delete> all [delete]]

get AccessEntry [default Target Name discovery]

AutoMap

Automatically maps all target devices visible to the iPBridge to iSCSI addresses. If you use no arguments, all devices are mapped to the default target. If you specify a target, all devices are mapped to that target. If you specify *, each device is mapped to its own auto-named target.

Automap <default * target name>

SaveConfiguration command required

AutoMapOnBootDelay

Specifies the duration of time in seconds that the iPBridge waits before performing an AutoMapOnBoot operation. AutoMapOnBoot must be enabled for the specified delay to take effect.

Default: 0

set AutoMapOnBootDelay [0 - 256] get AutoMapOnBootDelay

BridgeModel

Reports specific model and firmware information.

get BridgeModel

BridgeName

Specifies the eight-character ASCII name assigned to the iPBridge to identify individual units. It is not the World Wide Name. Changes take effect immediately.

set BridgeName [name]

SaveConfiguration Restart command required get BridgeName

ClearEventLog

Clears the contents of the event log. No new entries are recorded until the operation is completed.

ClearEventLog

vi

Image 35
Contents IPBridge 1550D Atto Technology, Inc Contents Appendix a Cabling Appendix C Safety standards and compliances XivUpdating firmware Interface optionsPage Atto iPBridge provides storage options FeaturesExhibit 1.0-1 Possible storage solutions using the iPBridge Physical components Exhibit 1.1-1 iPBridge 1550D back panel Installing Windows drivers InstallationUnpacking the packing box verifying contents Installing the iPBridgeUncheck the Require server verification check box Installing MS iSCSI Initiator for WindowsBeginning initial configuration Select Internet OptionsExpressWizard Configure the iPBridgePreliminary steps Page Target names Default target nodeAutomatically configure a single target Target managementClick on the Map each device to its own target button Automatically configure multiple targetsManually configure multiple target nodes Multiple target nodesExhibit 3.1-1 Target node configurations ISCSI ISCSI configurationChap commands EthernetPreliminary steps Modify passwordsSet up a Vlan Virtual Local Area Network Optional changesEnhance performance ISCSI performance configuration tool Windows onlySnmp Remote system monitoringUpdating firmware Using Atto ExpressNAVUsing FTP Check the host event log TroubleshootingCheck basic diagnostic tools Inside out methodCheck the serial port Check componentsCheck Scsi devices Check the iPBridge Scsi portCheck the LAN/WAN Check the iPBridge Ethernet portCheck the applications Performance issuesCheck the iSCSI OS driver Check the Operating SystemCheck the host system Optimize Atto ExpressNAV in Internet Explorer Reset to factory defaultsOpening an ExpressNAV session Using ExpressNAVUsing the serial port Interface optionsEnter Using TelnetExamples Appendix a CablingScsi cabling Cable typesEthernet connections Connecting Scsi devices to the Scsi portAppendix B CLI provides an ASCII-based interface Symbol IndicatesCLI summary CLI error messagesRmon Command Default ExampleAlphabetical CLI command explanations DeleteAllMaps DumpConfigurationDate FirmwareRestartISCSIChap IPGatewayIPSubnetMask ISCSIAliasRestoreConfiguration ISNSLoginControlPassword ReadOnlyPasswordRoute SaveConfigurationSCSIPortReset SCSIPortResetOnStartupSNMPDumpMIB SerialPortBaudRateSerialPortEcho SCSITargetLUNsVerboseMode SpeedWriteDefaultSNTPServer UsernameXiii FCC Standards Radio and Television Interference Appendix C Safety standards and compliancesPage Xvi

1550D specifications

ATTO Technology 1550D is an advanced Thunderbolt 3 to 10Gb Ethernet adapter designed to enhance networking capabilities for professionals, content creators, and businesses. Known for its compact design and robust performance, the 1550D is engineered to provide a seamless and efficient connection to high-speed networks, making it an ideal solution for a variety of demanding applications.

One of the standout features of the ATTO 1550D is its ability to support high-bandwidth data transfers. With Thunderbolt 3 technology, users can achieve speeds up to 40Gbps, allowing for quick and efficient file transfers. This is particularly beneficial for users dealing with large files, such as video editing and data-intensive graphic design, where every second counts.

The ATTO 1550D also supports 10Gb Ethernet connections, which enables users to connect to existing network infrastructures with ease. This dual compatibility ensures that professionals can maintain productivity and workflow without the need for extensive infrastructure upgrades. The adapter's support for both static and dynamic IP addressing adds an extra layer of versatility, catering to diverse networking environments.

In terms of characteristics, the ATTO 1550D features a compact and durable design, making it portable and easy to integrate into any workspace. The sleek form factor allows for straightforward connectivity, fitting effortlessly into modern setup configurations. Moreover, its plug-and-play functionality means that users can quickly establish connections without the need for extensive setup processes or additional drivers.

The adapter also boasts advanced features such as link aggregation, which allows for increased throughput and redundancy, enhancing overall network performance. This is crucial for organizations that require reliable network connections to maintain operational efficiency. The ATTO 1550D is built with high-quality components that ensure durability and longevity, ideal for both field and studio environments.

Overall, the ATTO Technology 1550D positions itself as a premier solution in the realm of Thunderbolt 3 to Ethernet adapters, combining speed, reliability, and flexibility. Whether used for high-speed data transfers or stable network connectivity, it meets the demands of today's high-performance computing environments, making it an essential tool for tech-savvy professionals and businesses alike.