Apple G5 specifications It stored on the arm Clamp Shaped bracket Screw

Page 43

If the rear posts of your rack are flush with the server’s back panel or within an inch of it, see “Attach the Cable-Management Arm to the Rack” on page 39 for mounting instructions.

Follow these steps to attach the arm to the left support brace.

1At the front of the server, loosen the thumbscrews securing it to the rack and slide the server a few inches forward.

Moving the server forward allows you to check the position of the cable-management arm after you mount it.

2Use a very small Phillips screwdriver to disconnect the small clamp that wraps around the long end of the cable-management arm (next to the two oval holes).

You’ll use this clamp and screw to attach the arm to the brace.

3Hold the cable-management arm with the long part closer to you and fold the hinged section of the long part away from you.

The hinged section is the part from which you removed the clamp and screw. This section should be perpendicular to the main part of the arm, with the oval holes farthest from you.

4Position the cable-management arm so that the hinged section is on the inside of the left brace, about 2 inches behind the server’s back panel.

Mount the cable-management arm as close to the back of the server as possible. Rotate the mounting plate on the arm so that it lies against the inside of

the U-shaped bracket. The U-shaped bracket should be sandwiched between the arm and the small clamp. Secure the clamp with the screw that held

it stored on the arm.

Clamp

U-shaped bracket

Screw

Cable-management arm

5Hold the arm in place and put the clamp you detached on the opposite side of the arm, so that the screw hole in the center shows through the open part of the brace.

6Insert the screw into its hole and tighten it so that the arm is fastened to the brace.

Chapter 3 Installing Your Server in a Rack

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents User’s Guide Apple Computer, Inc Apple Computer, Inc. All rights reserved Contents Starting Up From an External FireWire Optical Drive Updating or Installing Software on Xserve G5 SystemsInstalling or Restoring Software on Your Xserve G5 System Using a Second Xserve G5 System to Install Server SoftwareContents Page Introducing Xserve G5 Preface Introducing Xserve G5 Xserve G5 Overview Your Server at a Glance-Front Panel On/standby button and light Your Server at a Glance-Back Panel Power socket Your Server at a Glance-Interior Battery Your Cluster Node Server at a Glance Drive module and lights Your Server at a Glance-Mounting Hardware Four-post brackets Page Choose the Server’s Position in a Rack Preparing to Install Your ServerElectrical Power Rack Stability Operating EnvironmentConsiderations for Cables Security This chapter shows you how to install the server in a rack Installing Your Server in a RackGetting Ready to Install Determine the Position for the Server in the Rack There is one screw on either Side of the server Preparing the Server for InstallationInstalling Your Server in a Rack Installing Your Server in a Rack PCI-X card slots RAM slots Installing the Server in a Four-Post Rack or Cabinet Follow these steps to attach the server to the rack Some racks have Slide the brace Place the Server in the Rack Install the Cable-Management Arm and Cables Connect Cables to the Cable-Management Arm Attach the Cable-Management Arm to the Rack Remove and then reinstall the mounting screws one at a time Ethernet port Link lights Attach the Cable-Management Arm to the Support Brace It stored on the arm Clamp Shaped bracket Screw Power socket Gigabit Ethernet ports Installing Your Server in a Rack Installing the Server in a Short Four-Post Rack Some racks have Installing Your Server in a Rack Place the Server in the Rack Tighten the two thumbscrews to secure the server in the rack Installing the Server in a Two-Post Telco Rack Attach the cover to Installing Your Server in a Rack Connect Cables Directly to the Server Disconnecting Cables From the Server’s Back Panel Preparing the Server for Software Setup Starting Up the Server Using Your ServerWorking With Advanced Network Services Monitoring Status Lights and Other Indicators on the ServerSetting Up a Virtual Local Area Network Vlan Controlling Access to a Connected Keyboard and MouseEnabling Jumbo Ethernet Frames Changing the System Language Working With an Uninterruptible Power Supply UPSShutting Down the System Remotely To shut down from a network computer without Server Monitor If the Server Has a ProblemWhat to Do If Problem Try thisHard disk is erased or server Using Your Server On Xserve G5 Systems Installing or Restoring Software on Your Xserve G5 SystemTo use a second Xserve G5 system and command-line tools Using a Second Xserve G5 System to Install Server SoftwareTo start up from an external optical drive Starting Up From an External FireWire Optical DriveInstalling and Restoring From a Network Server Installing or Replacing Server Components Follow these steps to install or replace a drive module Installing or Replacing an Apple Drive ModulePress the drive module to pop out the handle Opening and Closing the Server Unscrew the two thumbscrews to release the server Pull the server out of the rack until it stops Adding Memory Follow these steps to install memory in the server Bank Installing a PCI-X Card or PCI Card Follow these steps to install a PCI-X card. or PCI card Installing a PCI-X Card or PCI CardAbout PCI-X Cards for the Server PCI-X card slots Slot covers Installing or Replacing Server Components Installing or Replacing Server Components Follow these steps to replace the lithium battery Replacing the BatteryInstalling or Replacing Server Components Ethernet Specifications Processor and Memory SpecificationsDimensions and Operating Environment Optical Drive SpecificationsUSB Specifications FireWire SpecificationsSerial Port Specifications Power Requirements for Devices You Can Connect Power SupplySystem Clock and Battery Page Important Safety Information Safety, Maintenance,Handling Your Computer Equipment Power SupplyProtecting Your Optical Drive Health-Related Information About Computer Use Cleaning Your EquipmentCleaning the Server’s Case Apple and the EnvironmentPage Laser Information Battery Disposal InformationHigh-Risk Activities Warning Page
Related manuals
Manual 22 pages 48.7 Kb Manual 13 pages 5.38 Kb Manual 112 pages 31.08 Kb Manual 120 pages 41.36 Kb Manual 112 pages 39 Kb Manual 8 pages 22.47 Kb

G5 specifications

The Apple G5, introduced in June 2003, marked a significant advancement in personal computing with its innovative architecture and powerful performance. It was the first desktop computer to feature a 64-bit architecture, which allowed it to process larger amounts of data more efficiently than its 32-bit predecessors. The G5 was equipped with the IBM PowerPC 970 processor, which operated at speeds ranging from 1.6 GHz to 2.7 GHz, making it a formidable contender in the market for both personal and professional use.

One of the standout features of the G5 was its aluminum chassis, which not only gave it a sleek and modern look but also aided in heat dissipation. The innovative design allowed the G5 to maintain lower operating temperatures regardless of the loads it handled. The G5 was famous for its quiet operation, thanks to a temperature-controlled, variable-speed fan system that minimized noise during regular use while still providing adequate cooling during intensive tasks.

In terms of memory, the G5 could support up to 8 GB of RAM, utilizing DDR SDRAM technology that provided enhanced performance in multitasking and complex applications. For graphics, the G5 offered powerful options, including dedicated GPU support from NVIDIA and ATI, enabling users to perform demanding tasks such as video editing and 3D graphics rendering with ease.

The connectivity options on the G5 were well thought out, including built-in USB 2.0 and FireWire 800 ports, which supported high-speed data transfer for external devices. In addition, the G5 featured an Ethernet port for networking capabilities, making it suitable for both home and office environments.

The G5 also ran on Mac OS X, which was optimized to take full advantage of its hardware capabilities. With its Unix-based foundation, Mac OS X provided users with a stable and secure operating environment, complete with a plethora of software applications tailored for creative professionals, including those in graphic design, video editing, and audio production.

Overall, the Apple G5 was a groundbreaking machine that successfully combined advanced technology, stylish design, and robust performance, earning a dedicated following among professionals and enthusiasts alike. Its legacy continues to influence Apple's approach to desktop computing, marking a pivotal moment in the evolution of personal computers.
Top Page Image Contents