Tripp Lite 1400-3000 VA owner manual Procedure, Replace Front Panel

Page 12

Battery Replacement

Under normal conditions, the original batteries in your UPS will last many years. See Safety sec- tion before replacing batteries. The batteries are designed for hot-swap replacement (i.e. leaving the UPS in ON mode), but some qualified service personnel may wish to put the UPS in the OFF mode and disconnect equipment before proceeding.

Procedure

1Remove Front Panel

2Disconnect Batteries

3Remove/Dispose of Batteries

4Add Batteries

5Connect Batteries

Attach connectors: black-to-black and red-to-red.

6Replace Front Panel

 

SMARTPRO UPS

1

￿

6

￿2

￿

5

￿3 4

FCC RADIO/TV INTERFERENCE NOTICE: (FOR CLASS A MODELS)

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. Operation of this equipment is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The user must use shielded cables and connectors with this product. Any changes or modifications to this product not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product name- plate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to the series number. The series number should not be confused with the marking name or model number of the product.

Tripp Lite has a policy of continuous improvement. Product specifications are subject to change without notice.

Note on Labeling

Two symbols are used on the label.

V~ : AC Voltage

V : DC Voltage

12

Image 12
Contents SmartPro Rackmount Intelligent, Line-Interactive UPS SystemsImportant Safety Instructions Battery WarningsUPS Location Warnings UPS Connection WarningsMounting Rack Post Telecom MountingMounting Tower Plug your equipment into the UPS Turn the UPS onUSB and RS-232 Serial Communications Buttons Front Panel Indicator Lights Front Panel Other UPS Features Rear Panel Basic Operation Service StorageProcedure Replace Front PanelManual del propietario Inteligentes e interactivos con la líneaInstrucciones de seguridad importantes Advertencias sobre la ubicación del UPSAdvertencias sobre la conexión del UPS Advertencias sobre la conexión de equiposMontaje Bastidor Montaje de 4 postesMontaje de 2 postes Telecomunicaciones Montaje En torre Conecte sus equipos en el UPS Encienda el UPSComunicaciones USB y serie RS-232 Todos los modelos Conexión de puerto EPO Todos los modelosConexión de batería externa Modelos exclusivos Botones Panel frontal Botón ON/OFF/STANDBY Encendido/Apagado/ReservaOperación básica continúa Luces indicadoras Panel frontalOtras funciones del UPS Panel posterior Operación básica continúa Servicio AlmacenamientoProcedimiento Recoloque el panel FrontalNota sobre el rotulado Manuel du propriétaire Mises en garde Emplacement de lUPS Directives de sécurité importantesMises en garde Connexions de lUPS Mises en garde Connexion déquipementMontage Bâti Bâti à quatre montantsMontage sur 2 montants Télécom Montage Tour Connecter votre équipement à lUPS Mettre lUPS sous tensionPorts de communication de série USB Et RS-232 Connexion au port EPO tous les modèlesConnexion de batterie externe Modèles sélect Boutons Panneau avant Fonctionnement de base, suite Voyants indicateurs Panneau avantAutres caractéristiques de lUPS panneau arrière Fonctionnement de base, suite Service EntreposageProcédure Replacer le panneau avant