Tripp Lite AGSMX500RT1U, AGSM7515RM1U, AGSM4878, AG-0019, AG-0018 owner manual Basic Operation

Page 10

201109267 93-2259-EN.qxd 10/21/2011 3:39 PM Page 10

Basic Operation continued

Accessory Slot: Remove the small cover panel from this slot to install optional accessories to remotely monitor and control your UPS. Refer to your accessory’s manual for installation instructions. Contact Tripp Lite Customer Support at (773) 869-1234 for more information, including a list of available SNMP, network management and connectivity products.

Power Sensitivity Adjustment (Select Models): This dial is normally set fully counter-clockwise, which enables the UPS to provide maximum protection against waveform distortions in its AC input. When such distortion occurs, the UPS will normally switch to providing sine wave power from its battery reserves for as long as the distortion is present. In areas with poor utility power or where the UPS’s input power comes from a backup generator, chronic waveform distortion could cause the UPS to switch to battery too frequently, draining its battery reserves. You may be able to reduce how often your UPS switches to battery due to moderate waveform distortion by experimenting with different settings for this dial. As the dial is turned clockwise, the UPS becomes more tolerant of variations in its input power’s AC waveform. NOTE: The further the dial is adjusted clockwise, the greater the degree of waveform distortion the UPS will allow to pass to connected equipment. When experimenting with different settings for this dial, operate connected equipment in a safe test mode so that the effect on the equipment of any waveform distortions in the UPS’s output can be evaluated without disrupting critical operations.

External Battery Connector (Select Models Only): Use to connect Tripp Lite external battery packs for additional runtime. The specifications section of this manual lists the Tripp Lite external battery packs that are compatible with your model. Refer to instructions available with the battery pack for complete con- nection information and safety warnings.

Input Breaker(s) (all models): Protect your electrical circuit from overcurrent draw from the UPS load. If these breakers trip, remove some of the load; then reset them by pressing the breaker(s) in.

Output Breaker(s) (select models): Protect your UPS from output overload. If one or more breakers trip, remove some of the load on the circuit(s), then reset them by pressing the breaker switch(es) in.

Ground Screw: Use this to connect any equipment that requires a chassis ground.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Intelligent, Line-Interactive UPS Systems Th Street, Chicago, IL 60609 USAUPS Location Warnings Important Safety InstructionsBattery Warnings UPS Connection WarningsMounting Rack Post MountingMounting Tower Post Telecom MountingTurn the UPS on External Battery Connection select models Buttons Front Panel ON/OFF/STANDBY ButtonIndicator Lights Front Panel Other UPS Features Rear Panel Basic Operation Service Storage1U UPS Models Procedure2U UPS Models Sistemas de UPS Inteligentes e Interactivos en Línea Th Street Chicago, IL 60609 USAAdvertencias sobre la conexión del UPS Instrucciones de seguridad importantesAdvertencias sobre la ubicación del UPS Advertencias sobre la conexión de equiposMontaje Bastidor Montaje de 4 postesMontaje de 2 postes Telecomunicaciones Montaje en bastidor continúaMontaje En torre Tolos los modelos de UPSEncienda el UPS Conexión de puerto EPO todos los modelos Comunicaciones USB y serie RS-232 todos los modelosConexión de batería externa modelos exclusivos Botones Panel frontal Botón ON/OFF/STANDBY Encendido/Apagado/ReservaOperación básica continúa Luces indicadoras Panel frontalOtras funciones del UPS Panel posterior Operación básica continúa Almacenamiento ServicioModelos de UPS de 2U ProcedimientoModelos de UPS de 1U Nota sobre el rotuladoNuméro de la série de lagence Systémes UPS intelligent, en attente activeTh Street Chicago, IL 60609 É.-U Mises en garde Connexions de lUPS Mises en garde Emplacement de lUPSDirectives de sécurité importantes Mises en garde Connexion déquipementMontage Bâti Bâti à quatre montantsMontage sur 2 montants Télécom Montage bâti suiteMontage Tour Tous les modèles dUPSFigure de la prise IEC320-C14 Connexion au port EPO tous les modèles Connexion de batterie externe modèles sélectBoutons Panneau avant Bouton ON/OFF/STANDBY Marche/Arrêt/AttenteFonctionnement de base, suite Voyants indicateurs Panneau avantAutres caractéristiques de lUPS panneau arrière Fonctionnement de base, suite Service EntreposageRemarque sur étiquetage ProcédureModèles UPS 2U               
Related manuals
Manual 13 pages 45.62 Kb

AG-0019, AG-0018, AGSM7515RM1U, AGSM4878, AGSMX500RT1U specifications

Tripp Lite is a leading manufacturer of power and connectivity solutions, and their range of products demonstrates a strong commitment to delivering reliability and performance. Among their notable offerings are the AGSM7515RM1U, AG-0018, AGSM4878, AG-0019, and AGSMX500RT1U models, which provide robust solutions for various applications.

The Tripp Lite AGSM7515RM1U is a 15U rackmount cabinet designed for optimal airflow and cooling. Its robust steel construction ensures durability, while the front and rear locking doors offer enhanced security for valuable equipment. The cabinet is equipped with adjustable mounting rails that accommodate a variety of devices and accessories. The included cooling fans are strategically positioned to maintain a stable temperature, reducing the risk of overheating.

The AG-0018 model is a versatile power strip that provides essential surge protection. It features eight outlets, making it ideal for managing multiple devices in a single location. With a built-in circuit breaker and EMI/RFI noise filtering, this power strip enhances equipment longevity and performance. Its compact design allows for easy installation in various environments, including workstations, server rooms, and home offices.

Tripp Lite's AGSM4878 is a specialized rack shelf designed to hold heavy equipment. With a weight capacity of up to 300 pounds, it is ideal for servers, UPS systems, and other substantial devices. The open design facilitates airflow and reduces heat build-up, while the installation is made simple by its compatibility with standard 19-inch racks. This shelf is essential for optimizing space and maintaining organized equipment layouts.

The AG-0019 is a high-performance HDMI extension cable that supports 4K resolution, ensuring crystal-clear video and audio transmission. Its durable construction and gold-plated connectors enhance connectivity and resistance to signal loss. This cable is perfect for professional AV applications, offering reliable performance in settings such as conference rooms and media centers.

Lastly, the AGSMX500RT1U is a compact UPS system that delivers reliable battery backup and surge protection for sensitive electronic equipment. With a power capacity of 500VA/300W, it provides ample runtime during power outages, allowing for safe data saving and system shutdown. Features include a USB port for management software integration and multiple outlets to accommodate various devices.

Together, these Tripp Lite products exemplify innovation and practicality, catering to the demands of modern technology environments. Each model is engineered to ensure maximum performance, longevity, and security, making them essential components for businesses and individuals alike.
Top Page Image Contents